| PUB. NO. | TITLE |
|---|---|
| S.I. 1110C | AC Fuel Pumps, Replacement |
| S.I. 1212 | Accelerator Pump, Marvel-Schebler Carburetors with - 0-235-C Series |
| S.I. 1351 | Accessory Drive Gear and Drive Shaft |
| S.I. 1203 | Accessory Drive Shaft Adapter Assy., Installation of Improved |
| S.I. 1145 | Accessory Drive Shaft, Modification to Incorporate Larger Spline Drive |
| S.I. 1171 | Accessory Housing and Covers, Salvage of |
| S.I. 1394 | Accessory Housing Assy. and Housing Cover Assy. Modification to Retrofit Hollow Oil Transfer Dowel |
| S.B. 247 | Accessory Housing, Modification of Oil Metering Plug |
| S.I. 1203 | Adapter Assy., Accessory Drive Shaft, Installation of Improved |
| S.I. 1295 | Adapter Bearing, Oversize Supercharger |
| S.I. 1436 | Adapter Kit for Magneto Isolation Drive |
| S.I. 1368 | Adapter Seal Washer and Retainer, Tachometer |
| S.I. 1329A | Adapter Seals, Supercharger Inlet |
| S.I. 1158 | Adapter, Magneto Drive, Replacement |
| S.B. 466 | Adapter, Oil Filter Base, Inspection |
| S.L. L218 | Adapters, Fuel Pump |
| S.L. L190 | Additive, Fuel, Use of " TCP " |
| S.L. L172B | Additive, Fuel, Use of Ethylene Glycol Monomethyl Ether (EGME) such as " Prist " |
| S.L. L226 | Additive, Oil P/N LW-16702, Discoloration |
| S.B. 471 | Additive, Oil Use of Avco Lycoming LW-16702 |
| S.B. 446C* | Additive, Oil Use of Avco Lycoming LW-16702 (A.D. #80-04-03) |
| S.I. 1409A | Additive, Oil, Use of Avco Lycoming LW-16702 (Refer to Supplement No. 1 to S.l. 1409A) |
| S.L. L154B | Adjustment Consideration for Returned and/or Run-Out Engines |
| S.B. 465C* | Aerobatic Engine Crankshaft Flange Inspection (A.D. #84-13-05) |
| S.B. 403 | Aerobatic Engine Lubricating Requirements |
| S.L. L208 | Aerobatic Engines, Breather Options |
| S.L. L202B | Aerobatic Maneuvers, Engines Installed in Aircraft Used for, All 320, 360 and 540 Series Using Crankshafts w/ Lightning Holes |
| S.B. 509 | Aeroquip Service Bulletin No. AA135, " 601 Hose Assemblies " |
| S.I. 1464 | Aeroquip Service Bulletin No. AA91, " Hose Line Problems " |
| S.I. 1002 | Air Filters, Carburetor, Proper Maintenance |
| S.I. 1396 | Air Housing, Induction, Redesigned |
| S.B. 417 | Air Inlet Housing |
| S.B. 401 | Aircraft Struck by Lightning, Recommendations |
| S.I. 1427B | Aircraft, Engine Test after Overhaul with Engine Installed in |
| S.B. 361 | AiResearch Bulletin No. 1172-1A, " Turbocharger Modification " |
| S.B. 347 | AiResearch Bulletin No. 571-1, " Turbine Housing Inspection & Replacement " |
| S.B. 329A | AiResearch Bulletin No. TP60-0100, " Turbine Housing Inspection " |
| S.B. 383 | AiResearch Bulletin No. TP60-0101, " Inspection of Model T1823 Turbocharger w/ Stainless Steel Turbine Housings " |
| S.B. 379 | AiResearch Bulletin No. TP60-0103, " Inspection of Remanufactured Waste Gate Valve Assy. " |
| S.B. 391A | AiResearch Bulletin No. TP60-0105, " Turbocharger Repl. or Mod. " (Refer to Supplement No. 1 to S.B. 391A) |
| S.B. 440 | AiResearch Bulletin No. TP60-0115, " Spring Pin Replacement - Variable Absolute Pressure Controllers " |
| S.B. 450 | AiResearch Bulletin No. TP60-0119, " Bypass Valve Modification" |
| S.B. 452A | AiResearch Bulletin No. TP60-0121, " Turbo Inspection " |
| S.I. 1223 | AiResearch Instruction No. 969-1, " Freeing Turbine Shaft " |
| S.I. 1328 | AiResearch Letter No. TP61-0002, " Turbocharger Replacement " |
| S.I. 1416 | AiResearch Letter No. TP61-0039, " Turbocharger Bypass Valve Modification " |
| S.L. L231 | AiResearch Turbo Control Test Set P/N 481070-1, Variable Absolute Pressure Controller Calibration Values |
| S.B. 484* | Alignment, Inspection and Modification of Crossover Exhaust Assembly (A.D. #89-12-04) |
| S.B. 213A | Allen Head Nuts (Cylinder Base), Replacing Cylinder Base Spline Nuts with |
| S.L. L142B | Alterations, Policy Relative to Affecting Engine Performance |
| S.B. 386 | Alternator Bearing Lubrication - TIGO-541-E |
| S.I. 1254 | Alternator Belt Replacement |
| S.I. 1129A | Alternator Belt Tension, Methods of Checking |
| S.B. 511 | Alternator Bracket Installation |
| S.B. 356 | Alternator Bracket Support, Addition of - TIO-540-A2C |
| S.I. 1283A | Alternator Cog Belt and Pulley Installation |
| S.I. 1330A | Alternator Drive Coupling, Spring Loaded - TIGO-541-E |
| S.I. 1266 | Alternator Ground Strap - All Engines with Prestolite |
| S.I. 1270A | Alternator Mounting Bracket Shims |
| S.I. 1249 | Alternator Pulley and Shaft Assy. |
| S.I. 1259 | Alternator Replacement-VO-435-B1A |
| S.I. 1253 | Alternator, Prestolite Bulletin No. ASM-5, " Field Terminal Stud Insulation Replacement " |
| S.I. 1237A | Alternator, Prestolite Bulletins No. ASM-3 & ASM-4, " Aircraft Charging System Service Precautions " |
| S.I. 1451A | Alternator, Starter and Compressor Installation |
| S.I. 1105A | Alternator/Generator Mounting Brackets, Periodic Inspection |
| S.I. 1154E | Alternators, FAA Approved |
| S.L. L147B | Anderol 471 All-Climate Synthetic Aircraft Lubricant |
| S.I. 1454 | Arm, Rocker, Parallel Valve Installation |
| S.I. 1210B* | Attaching Nut Replacement, Pinion Cage (A.D. #69-25-08) |
| S.I. 1196 | Attaching Studs, Replacement of Reduction Gear |
| S.I. 1076 | Backlash, Bevel Gear Assys., Pitch Alignment and |
| S.B. 489A | Baffle Assembly, P/N LW-13383, Oil Sump |
| S.I. 1279A | Baffle Replacement, Oil Sump |
| S.I. 1363 | Ball Joint and Retaining Strap, Exhaust Manifold |
| S.I. 1292A | Bearing and Lubrication Modifications, Stainless Steel Thrust |
| S.I. 1377 | Bearing Bore Repair, Crankcase Main, and Oversize Main Bearings (Refer to Supplement No. 1 to S.I. 1377) |
| S.B. 326A* | Bearing Dowel Replacement, Crankcase (A.D. #'s 71-05-02 & 72-21-06) |
| S.I. 1225D | Bearing Dowel, Crankcase, Replacement |
| S.I. 1250 | Bearing Lubrication, Propeller Shaft |
| S.I. 1177B | Bearing Repair, Governor Drive, in Crankcase |
| S.I. 1020B | Bearing Replacement, Crankshaft Main |
| S.I. 1312 | Bearing Replacement, Propeller Drive Thrust (Crankcase P/N LW-13082) |
| S.I. 1149 | Bearing Support Web, Crankcase, Inspection & Modification |
| S.I. 1108C | Bearing Surfaces, Propeller Shaft, Repair |
| S.B. 386 | Bearing, Alternator, Lubrication |
| S.B. 327C* | Bearing, Inspection of Center Main (A.D. #'s 71-05-02 & 72-21-06) |
| S.I. 1295 | Bearing, Oversize Supercharger Adapter |
| S.I. 1356 | Bearing, Oversize Thrust, for Reduction Gear |
| S.B. 390A | Bearing, Propeller Thrust (LW-12978), Inspection |
| S.B. 276 | Bearing, Replacement of Front Main at Overhaul |
| S.B. 371A* | Bearings, High-Crush, New Rod Kits (A.D. #73-05-01) |
| S.I. 1432A | Bearings, Installation of High-Crush, Thin-Wall Rear Main in Crankcases without Retention Dowels |
| S.I. 1283A | Belt and Pulley, Alternator Cog, Installation |
| S.I. 1129A | Belt Tension, Alternator, Method of Checking |
| S.I. 1254 | Belt, Alternator, Replacement |
| S.I. 1252C | Bendix 1200 Series Magneto Installation |
| S.B. 516 | Bendix and TCM S-20 and S-1200 Series Impulse Coupling Magnetos, Inspection and Removal |
| S.I. 1276 | Bendix Electrical Components Bulletin No. 529A, " Torque Values for Drive Shaft Nut " |
| S.I. 1365 | Bendix Electrical Components Bulletin No. 597, " Cleaning Ignition Harness Spark Plug Ends " |
| S.I. 1375 | Bendix Electrical Components Bulletin No. 603, " Ign. Noise in Aircraft Communications Equipment " |
| S.B. 305B* | Bendix Fuel Injector Bulletin No. 18, Rev. 4, " Replacement of Bendix Fuel Diaphragm Assy. " (A.D. #67-22-06) |
| S.I. 1166A | Bendix Fuel Injector Bulletin No. 20, Rev. 2, " Identifying Fuel to Air Seal Leak " |
| S.I. 1244 | Bendix Fuel Injector Bulletin No. RS-35, " Changes, - Regulator & Fuel Control System " |
| S.I. 1247 | Bendix Fuel Injector Bulletin No. RS-37, " Replacement of Idle Valve Lever Assy. " |
| S.B. 382* | Bendix Fuel Injector Bulletin No. RS-43, " Inspection & Modification of Flow Dividers " (A.D. #75-09-15) |
| S.B. 428* | Bendix Fuel Injector Bulletin No. RS-52, " Mod. of RSA-5AB1, RSA-5AD1 & RSA-10AD1 " (Refer to Supplement No. 1 to S.B. 428) (A.D. #78-23-10) |
| S.B. 429* | Bendix Fuel Injector Bulletin No. RS-53 ," Modification of RSA-7AA1 " (A.D. #78-23-10) |
| S.B. 430* | Bendix Fuel Injector Bulletin No. RS-54, " Mod. of RSA-lODB1, RSA-1ODB2 & RSA-1OED1 " (Refer to Supplement No. 1 to S.B. 430) (A.D. #78-23-10) |
| S.B. 433A* | Bendix Fuel Injector Bulletin No. RS-57, Rev. 1, " Inspection of Fuel Diaphragm Assy. P/N 2529471 " (A.D. #79-0405) |
| S.B. 444A* | Bendix Fuel Injector Bulletin No. RS-62, Rev. 2, " Modification of Mixture Control Shaft Assy. " (A.D. #81-03-05) |
| S.B. 445 | Bendix Fuel Injector Bulletin No. RS-63, " Inspection of Fuel Diaphragm Assy. " |
| S.B. 441 | Bendix Fuel Injector Bulletin No. RS-66, " Modification of Idle Valve Assy. " |
| S.B. 442* | Bendix Fuel Injector Bulletin No. RS-68, " Integrity Inspection of Regulator Stem Nut " (Refer to Supp. No. 1 to S.B. 442) (A.D. #'s 79-21-08 & 79-26-03) |
| S.I. 1414A | Bendix Fuel Injector Bulletin No. RS-77, Rev. 1, " Air Bleed Nozzle, RS & RSA Fuel Injection Systems, Two Piece Assembly " |
| S.B. 467* | Bendix Fuel Injector Bulletin No. RS-88, " Deter. of Fuel Diaphragm Change " (Refer to Supplements No. 1 & 2 to S.B. 467) (A.D. #83-22-04) |
| S.I. 1378 | Bendix Fuel Injector Bulletin No. SSB-317, " Overheating Bendix Fuel Injectors & Carburetors " |
| S.I. 1404A | Bendix Fuel Injector Bulletin No. SSB-318, " Overhaul Periods for Bendix Fuel System Components " |
| S.I. 1335 | Bendix Fuel Injector Letter No. 22, " Mixture Control Maintenance " |
| S.B. 443* | Bendix Fuel Injector No. RS-69, " Integrity Inspection of Regulator Stem Nut " (A.D. #79-21-08) |
| S.L. L221 | Bendix Fuel Metering Components, Warranty Repair of |
| S.B. 340 | Bendix Magneto Bulletin No. 530A, " Securing Coil Clamp " |
| S.I. 1260 | Bendix Magneto Bulletin No. 533A, " Acceptable Stress Relief Fissures, Flow Lines & Cracks " |
| S.I. 1226 | Bendix Magneto Bulletin No. 545, " Tubing for S-1200 Cover Hold Down Screw " |
| S.B. 341 | Bendix Magneto Bulletin No. 549, " Locating Shoulder for Carbon Brush Spring " |
| S.B. 343B | Bendix Magneto Bulletin No. 551A, " New Distributor Block Lubricant " |
| S.B. 376* | Bendix Magneto Bulletin No. 556B, " Magneto Drive Shaft Bushing Change " (A.D. #74-26-09) |
| S.I. 1282 | Bendix Magneto Bulletin No. 560, " Replacement of Transformer Coils & Rotating Magnets " |
| S.B. 373 | Bendix Magneto Bulletin no. 566, " S-1200 Distributor Block & Gear Change " (Refer to Supplement No. 1 to S.B. 373) |
| S.I. 1332 | Bendix Magneto Bulletin No. 573, " Green Distributor Blocks " |
| S.I. 1327 | Bendix Magneto Bulletin No. 580, " Breaker Securing Screws " |
| S.B. 416A* | Bendix Magneto Bulletin No. 584B, " Coil Retaining Devices, D2000/D2200 Mags " (A.D. #78-18-04) |
| S.B. 410* | Bendix Magneto Bulletin No. 587, " Inspection D2000 Capacitors & Lead Crimp Terminals " (A.D. #78-18-04) |
| S.I. 1367 | Bendix Magneto Bulletin No. 588, " Stress Lines in Distributor Blocks " |
| S.B. 414* | Bendix Magneto Bulletin No. 589, " Rear Bearing Lubrication, D2000/D2200 Mags " (A.D. #77-17-07) |
| S.B. 415A* | Bendix Magneto Bulletin No. 590A, " Rotating Magnet to Housing Clearance, D2000/D2200 Mags " (A.D. #78-18-04) |
| S.I. 1382 | Bendix Magneto Bulletin No. 592, " Inspection of Breaker Contact Assys. & Capacitor Flag Terminal Crimps " |
| S.B. 425B* | Bendix Magneto Bulletin No. 599A, " Inspection & Replacement of Impulse Coupling & Stop Pins " (A.D. #78-09-07) |
| S.B. 427A | Bendix Magneto Bulletin No. 600, " IO-353110 Bearing in D2000/D2200 Mags " |
| S.B. 438A* | Bendix Magneto Bulletin No. 605A, " Housing Distortion & Coil Retention " (A.D. #80-17-14) |
| S.B. 437* | Bendix Magneto Bulletin No. 606, " D2000/D2200 Magnetos Using Green Distributor Blocks " (A.D. #79-12-07) |
| S.I. 1400 | Bendix Magneto Bulletin No. 608, " Self-Locking Cam Retaining Screws " |
| S.B. 458 | Bendix Magneto Bulletin No. 613, " Inspection and/or Replacement of Green Distributor Blocks " |
| S.B. 461 | Bendix Magneto Bulletin No. 617, " Inspection or Replacement of Distributor Gears " |
| S.B. 459* | Bendix Magneto Bulletin No. 618, " Inspection or Replacement of Distributor Gears " (A.D. #81-12-06) |
| S.B. 460 | Bendix Magneto Bulletin No. 619, " Inspection or Replacement of Distributor Gears " |
| S.B. 464A* | Bendix Magneto Bulletin No. 623A, " Inspection of Impulse Coupling Cam Assys. " (A.D. #82-20-01 |
| S.L. L207 | Bendix Magneto Bulletin No. 625, " Broken Coil Securing Clamps, P/N 10-50765 " |
| S.I. 1433 | Bendix Magneto Bulletin No. 626, " Installation of Impulse Coupling Assemblies " |
| S.B. 469 | Bendix Magneto Bulletin No. 627, " Distributor Block Kit P/N 10-682056 (6 cyl.) Dual Magneto Series " |
| S.B. 470 | Bendix Magneto Bulletin No. 628, " Replacement of Impulse Coupling Main Spring P/N IO-382941 " |
| S.B. 474 | Bendix Magneto Bulletin No. 629, " Insp. & Repl. of Brown Magneto Blocks on Turbocharged (6 cylinder) Engines " |
| S.B. 365 | Bendix Magneto Conversion to Incorporate Flexible Drive |
| S.I. 1346A | Bendix S4LN-1208 Magnetos, Installation of |
| S.L. L188 | Black Oxide Finish, Cylinders Treated with |
| S.L. L196 | Blade, Screwdriver, ST-418-3, Revision to |
| S.I. 1352A | Body Disassembly, Hydraulic Lifter |
| S.I. 1336 | Body Identification, Tappet |
| S.I. 1307B | Bolt Assembly, Connecting Rod, and Torque Application |
| S.I. 1209B* | Bolt Replacement, Crankshaft Flange (A D. #80-04-04) |
| S.I. 1459 | Bolt Threads, Application of Sealant |
| S.I. 1450 | Bolt, Connecting Rod and Torque Application, Alternate |
| S.I. 1170 | Bolt, Generator Mounting, Replacement |
| S.B. 372B | Bolt, T. High-Tensile Clamping Bands |
| S.I. 1469 | Bolts, Connecting Rod with High-Tensile Strength |
| S.I. 1213 | Bolts, Connecting Rod, Increased Torque Value |
| S.B. 363 | Bolts, Connecting Rod, Part Number Listing PC-206: IO-360 Series Engines |
| S.I. 1458 | Bolts, Connecting Rod, Soft |
| S.I. 1318 | Bolts, Connecting Rod, Strengthened |
| S.I. 1029D | Bolts, Crankcase, Tightening Procedures for Thru-Studs and (Refer to Supplement Nos. 1 and 2 to S.I. 1029D) |
| S.I. 1248B | Bolts, E engine Mounting Bracket Attaching |
| S.I. 1380* | Bolts, Engine Mounting Bracket Attaching Nuts or (A D. #79- 10-03) |
| S.B. 491A* | Bolts, Exhaust Transition, Inspection of (AD. #91-10-04) |
| S.B. 371A* | Bolts, High Tensile Strength, Connecting Rod Assys. in new Rod Kits) (AD. #73-05-01) |
| S.I. 1323A | Bolts, High Tensile Strength, Connecting Rods with |
| S.I. 1311A | Bolts, Oversize Connecting Rod |
| S.I. 1417 | Bore Repair, Crankcase Gear Shaft |
| S.I. 1377 | Bore Repair, Crankcase Main Bearing, and Oversize Main Bearings (Refer to Supplement No. 1 to S.I. 1377) |
| S.I. 1334A | Bore Repair, Crankcase Tappet |
| S.I. 1315A | Bracket and Clamp Installation, Turbocharger Strut |
| S.I. 1248B | Bracket Attaching Bolts, Engine Mounting |
| S.I. 1380* | Bracket Attaching Nuts or Bolts, Engine Mounting (A D. #79- 10-03) |
| S.I. 1306A | Bracket Installation, Compressor Mounting |
| S.B. 356 | Bracket, Addition of Alternator Support - TIO-540 A2C |
| S.B. 511 | Bracket, Alternator Installation |
| S.I. 1270A | Bracket, Alternator Mounting, Shims |
| S.I. 1339A | Bracket, Turbocharger |
| S.B. 463 | Bracket, Turbocharger Mounting, Inspection |
| S.I. 1105A | Brackets, Generator/Alternator Mounting, Periodic Inspection |
| S.I. 1397 | Breather Fitting, Overflow Oil from, of Inverted Oil System |
| S.L. L208 | Breather Options for Aerobatic Engines |
| S.I. 1366A | Bushing Hole, Rocker Shaft Repair Procedure for Worn |
| S.I. 1098E | Bushing Location, Propeller Flange |
| S.I. 1143B | Bushing Replacement in Counterweights and Bushing Tooling Update (Refer to Supplement No. 1 to S.I. 1143B) |
| S.I. 1044 | Bushing Replacement, Rear Crankshaft Spline |
| S.I. 1386A | Bushing, Magneto Drive Gear, Replacement of Damaged or Worn |
| S.I. 1142B | Bushings, Crankshaft Counterweight, Replacement |
| S.I. 1208 | Bushings, Magneto Shaft Bore, Installation of |
| S.I. 1452 | Bushings, Propeller Flange, Reindexing (0-360-C1G) |
| S.B. 253A | Bushings, Replacement of Propeller Flange |
| S.I. 1316A | Bypass Valve Seat, Oil Cooler, Repair of |
| S.I. 1214A | Bypass Valve, Exhaust: Reset for Increased Critical Altitude |
| S.I. 1442 | Bypass Valve, Oil Filter, Improved |
| S.I. 1423 | Bypass Valve, P/N 75944, Thermostatic Oil Cooler |
| S.I. 1255 | Bypass Valve, Thermostatic Oil Cooler, Replacement |
| S.I. 1008B | Bypass, Thermostatic Oil Cooler, Instructions for Installation |
| S.I. 1294 | Cable Routing, Alternate Ignition |
| S.L. L206A | Cam Followers/Tappet Bodies, Field-Reconditioned |
| S.I. 1439 | Camshaft and Gear Assembly, New integral, Installation (Refer to Supplement No. 1 to S.I. 1439) |
| S.I. 1016C | Camshaft and Gear Replacement - O & IO-540 Series |
| S.L. L214A | Camshaft Exchange Program, Reconditioned Notice of Discontinuance of Program) |
| S.I. 1218A | Camshaft w/ Integral Drive Gear, Parts Substitution Chart |
| S.B. 293B* | Camshaft, Installation of New (A.D. #63-23-02) |
| S.I. 1182A | Camshaft, Modified for Improved Performance - GO-480 Series |
| S.I. 1350A | Camshaft, Redesigned, for HI0-360-D1A Engines |
| S.I. 1263B | Camshaft, Redesigned, for IO-360 Series Engines |
| S.I. 1359 | Cap Modification, Connecting Rod |
| S.I. 1002 | Carburetor Air Filters, Proper Maintenance |
| S.I. 1206 | Carburetor Float Clearance, Checking |
| S.I. 1148B | Carburetor Heat Control, Use of |
| S.I. 1390 | Carburetor Idle Tube Replacement |
| S.I. 1428 | Carburetor Modification for Richer Power Setting - O/LO-360-A |
| S.I. 1393 | Carburetor Modification Kit |
| S.I. 1398A | Carburetor Modification Marvel-Schebler- 0-540 |
| S.I. 1421 | Carburetor Modification Marvel-Schebler- TO-360 |
| S.I. 1271A | Carburetor Nozzle Replacement- 0-235 |
| S.I. 1395A | Carburetor Nozzle Replacement - 0-320-D2A |
| S.I. 1305C | Carburetor Nozzle Replacement - 0-320-E2A, -E2D, -E2G, -E3D |
| S.B. 409* | Carburetor Replacement (A.D. #77-13-16) |
| S.B. 258 | Carburetor Setting Change to Eliminate Engine Roughness - Piper Aircraft |
| S.B. 330B* | Carburetor Throttle Arm Screw, Retighten and Lockwire A.D. #72-06-05) |
| S.B. 366 | Carburetor Throttle Body Screw Inspection |
| S.I. 1161 | Carburetor Throttle Shaft, Modification to Prevent Leakage |
| S.B. 504* | Carburetor, Consolidated Fuel Systems Inc. Bulletin No. CF1-92, Rev. 1, " Carburetor Float Kit CF666-915 " (A.D. #93-10-04) |
| S.B. 481 | Carburetor, Facet Aerospace Products Bulletin No. A1-87, " Carburetor Return and Inspection " |
| S.B. 483 | Carburetor, Facet Aerospace Products Bulletin No. A1-88, " Possible Loose 62-226 Pins " |
| S.L. L186 | Carburetor, Marvel-Schebler Bulletin No. A1-76, " Carburetor Cleaning |
| S.I. 1370 | Carburetor Marvel-Schebler Bulletin No. A1-78 " Carburetor Mixture Control Retainer " |
| S.B. 434* | Carburetor Marvel-Schebler Bulletin No. A1-79 " Improved Sealing of Economizer Channel HA-6 Carburetors " (A.D. #79-15-02) |
| S.I. 1413 | Carburetor Marvel-Schebler Bulletin No. A1-81, " Model HA Carburetor Float Shaft and Bracket Wear " |
| S.I. 1373 | Carburetor Marvel-Schebler Bulletin No. A2-78, " Sealing Pump & Economizer Rods " |
| S.B. 436* | Carburetor, Marvel-Schebler Bulletin No. A2-79, " Possible Carburetor Contamination " A.D. #79-08-06) |
| S.B. 310 | Carburetor, Marvel-Schebler Bulletin No. A3-66, " Replacement of Venturi " |
| S.B. 297A* | Carburetor, Marvel-Schebler MA-4-5, One Piece and Main Venturi A.D. #63-22-03) |
| S.I. 1212 | Carburetor, Marvel-Schebler with Accelerator Pump - 0-235-C Series |
| S.B. 352 | Carburetor, Marvel-Schebler/Tillotson Bulletin No. 1-71, " Securing Cam Lever " |
| S.B. 495A | Carburetor, Precision Airmotive Corp. Bulletin No. MSA-1, Rev. 1, " Replacement of Composite Floats with Metal Floats " |
| S.B. 498B | Carburetor, Precision Airmotive Corp. Bulletin No. MSA-2, Rev. 2, " One Piece Primary and Main Venturi " |
| S.B. 327C* | Center Main Bearing Inspection A.D. #'s 71-05-02 & 72-21-06) |
| S.I. 1418 | Chamber Cleaning Procedure, Combustion |
| S.I. 1403 | Champion Bulletin No. 75-4, Approved Spin-On Oil Filters |
| S.I. 1315A | Clamp and Bracket Installation, Turbocharger Strut |
| S.B. 342B* | Clamp Inspection and Installation, Support, and Fuel Line (A.D. #92-12-10) |
| S.B. 3 72B | Clamping Bands, High-Tensile T- Bolts |
| S.I. 1355 | Clamps and Extensions, Intake Pipes |
| S.I. 1361 | Clamps, T-Bolt Hose |
| S.I. 1116C | Clearance Modification, Exhaust Valve to Guide |
| S.I. 1206 | Clearance, Checking Carburetor Float |
| S.I. 1392 | Cold Weather Operation and Engine Lubricating Oil Recommendations |
| S.I. 1181 | Color Code on Cylinders for Avco Lycoming Engines |
| S.I. 1418 | Combustion Chamber Cleaning Procedure |
| S.I. 1191 | Compression, Cylinder |
| S.I. 1306A | Compressor Mounting Bracket Installation |
| S.I. 1232 | Compressor Mounting Plate Assembly Procedure - TIGO-541 |
| S.B. 344 | Compressor Mounting Plate Assembly Procedure - TIO & TIGO-541 . |
| S.I. 1192 | Compressor NO ST 266, Valve Spring |
| S.I. 1451A | Compressor, Starter and Alternator Installation |
| S.I. 1467 | Connecting Rod Assemblies |
| S.I. 1466 | Connecting Rod Assemblies |
| S.B. 302A* | Connecting Rod Assemblies, P/N's 74308 & 74503, Replacement in IO-360-A1A Engines A.D. #66-06-03) |
| S.B. 371A* | Connecting Rod Assembly w/ High Tensile Strength Bolts (New Rod Kits w/ High-Crush Bearings) A.D. #73-05-01) |
| S.I. 1450 | Connecting Rod Bolt and Torque Application, Alternate |
| S.I. 1307B | Connecting Rod Bolt Assembly and Torque Application |
| S.I. 1106D | Connecting Rod Bolt Nut Crimping Requirements |
| S.B. 363 | Connecting Rod Bolt Part Number Listing - PC-206; IO-360 Series Engines |
| S.I. 1213 | Connecting Rod Bolts, Increased Torque Value |
| S.I. 1311A | Connecting Rod Bolts, Oversize |
| S.I. 1458 | Connecting Rod Bolts, Soft |
| S.I. 1318 | Connecting Rod Bolts, Strengthened |
| S.I. 1359 | Connecting Rod Cap Modification |
| S.I. 1469 | Connecting Rod with High Tensile Strength Bolts |
| S.B. 351 B* | Connecting Rods (Heavy) For High Speed Geared Drive Engines (A.D. #74-13-05) |
| S.I. 1323A | Connecting Rods with High-Tensile Strength Bolts |
| S.B. 439A | Connecting Rods, Inspection for Fretting and/or Galling, Repair of Fretting |
| S.I. 1138B | Connecting Rods, Replacement for 10-720 Series Engines |
| S.B. 504* | Consolidated Fuel Systems, Inc. Bulletin No. CF1-92, Rev. 1, " Carburetor Float Kit CF666-915 " (A.D. #93-19-04) |
| S.I. 1435 | Constant Speed to Fixed Pitch Propeller Conversion, and Vice Versa (Refer to Supplement No. 1 to S.I. 1435) |
| S.B. 418 | Control Cable Rod End Replacement Waste Gate |
| S.I. 1211D | Controller Linkage and Fuel injector Setting |
| S.B. 440 | Controller, AiResearch Bulletin No. TP60-0115, " Spring Pin Replacement " |
| S.L. L231 | Controller, Variable Abs., Pressure Calibration Values for AiResearch Turbo Control Test Set P/N 481070-1 |
| S.I. 1463 | Controllers, Improved for TIO-540-AE2A Engine Model |
| S.I. 1435 | Conversion from Constant Speed to Fixed Pitch Propeller and Vice Versa (Refer to Supplement No. 1 to S.I. 1435) |
| S.L. L204 | Conversion Kit P/N LW-18866, Fuel Injection |
| S.B. 246 | Conversion of GO-435-C2B and -C2B2 to GO-435-C2B-6 and -C2B2-6 |
| S.L. L156 | Conversion of 0-290-G Surplus Power Plant Engines to 0-290-D Engines (FAA Release NO 462) |
| S.I. 1246 | Conversion, Engine, for Use of 100/130 Grade Fuel |
| S.I. 1383 | Conversion, Starter |
| S.I. 1453 | Converter Plate Gasket, Oil Filter, Replacement of |
| S.L. L216 | Copyright of Avco Lycoming Williamsport Publications |
| S.B. 394 | Corner Radii, Counterweight Inspection |
| S.I. 1142B | Counterweight Bushings, Crankshaft, Replacement |
| S.B. 394 | Counterweight Inspection for Corner Radii |
| S.I. 1152A | Counterweight Lobes, Crankshaft, Punch Marks |
| S.B. 245D | Counterweight System, Dynamic, Detuning |
| S.L. L217 | Counterweight Tooling Update Kits |
| S.B. 333 | Counterweight, Inspection and Replacement |
| S.I. 1143B | Counterweights, Bushing Replacement and Tooling Update (Refer to Supplement No. 1 to S.l. 1143B) |
| S.I. 1012F | Counterweights, Location and Proper Assembly Procedure |
| S.I. 1130 | Counterweights, Marking or Identifying |
| S.I. 1330A | Coupling, Alternator Drive, Spring Loaded - TIGO-541-E |
| S.B. 395 | Coupling, Transition, Replacement |
| S.B. 492A | Couplings, Redesigned V-Band, for Tailpipe Installation |
| S.I. 1238A | Couplings, V-Band, Assembly and Torque Procedures |
| S.I. 1394 | Cover Assy., Accessory Housing, Modification to Retrofit Hollow Oil Transfer Dowel |
| S.I. 1171 | Covers and Accessory Housings, Salvage of |
| S.L. L228 | Cracking of Cylinder Head Exhaust Port |
| S.I. 1225D | Crankcase Bearing Dowel Replacement |
| S.B. 326A* | Crankcase Bearing Dowel Replacement (A D. #'s71-05-02 & 72-21-06) |
| S.I. 1149 | Crankcase Bearing Support Web, Inspection &Modification |
| S.B. 273A | Crankcase Center Main Bearing Support Modification to Incorporate Body Fit Thru-Studs |
| S.I. 1417 | Crankcase Gear Shaft Bore Repair - (Dual Magnetos) |
| S.1.1377 | Crankcase Main Bearing Bore Repair and Oversize Main Bearings (Refer to Supplement No. 1 to S.I. 1377) |
| S.I. 1159 | Crankcase Modification to Prevent Reduction Gear Housing Interference |
| S.I. 1312 | Crankcase P/N LW-13082, Propeller Drive Thrust Bearing Replacement |
| S.I. 1125B | Crankcase Parting Surface Sealants, Alternate |
| S.I. 1326 | Crankcase Repair (Thru-Stud Spotface) |
| S.B. 353A | Crankcase Replacement- TIO-541-E Series |
| S.I. 1334A | Crankcase Tappet Bore Repair |
| S.I. 1290D | Crankcase Thru-Stud Locations, Repair of Oil Leakage, Assembled and Unassembled Engines |
| S.I. 1029D | Crankcase Thru-Studs and Bolts, Tightening Procedures (Refer to Supplement No. 1 & 2 to S.l. 1029D) |
| S.I. 1354B | Crankcase Thrust Face Repair |
| S.I. 1177B | Crankcase, Governor Drive Bearing Repair |
| S.I. 1185 | Crankcase, Interference Between Crankshaft and |
| S.B. 392B | Crankcase, Reinforced - TIO/LTIO-540 (Refer to Supplement No. 1 and 2 to S.B. 392B) |
| S.I. 1140 | Crankcase, Salvage Repair of Magneto Bearing Recess |
| S.I. 1406B | Crankcases with Provision for Large-Diameter Hydraulic Lifters |
| S.I. 1432A | Crankcases without Retention Dowels, Installation of High-Crush, Thin-Wall Rear Main Bearings in |
| S.B. 472 | Crankcases, Disassembly of Wide Cylinder Flange |
| S.I. 1112E | Crankcases, Repair of Fretted (Refer to Supplement No. 1 to S.l. 1112E) |
| S.I. 1345 | Crankcases, Service Replacement for Narrow Cylinder Flange Four Cylinder Engines |
| S.I. 1465 | Crankshaft Assemblies for Non-Counterweighted Engine Models |
| S.B. 422A* | Crankshaft Assembly Replacement (A D. #78-12-09) |
| S.I. 1113A | Crankshaft Assembly, Revised to Eliminate Sludge Tubes |
| S.I. 1296 | Crankshaft Attaching Parts and Drive Plate |
| S.B. 272A | Crankshaft Center Main Journal, Retorqueing of Thru-Studs to Assure Positive Clearance |
| S.I. 1142B | Crankshaft Counterweight Bushings, Replacement |
| S.I. 1152A | Crankshaft Counterweight Lobes, Punch Marks |
| S.B. 482 | Crankshaft Flange Area Cracking |
| S.I. 1209B* | Crankshaft Flange Bolt Replacement(AD. #80-04-04) |
| S.B. 465C* | Crankshaft Flange Inspection for Aerobatic Engines (A.D. #84-13-05) |
| S.B. 201E | Crankshaft Flanges, Inspection and Straightening of Bent |
| S.I. 1251 | Crankshaft Front Oil Plug, Parts Catalog PC- 111 & PC- 112 Listing |
| S.I. 1180B | Crankshaft Front Plug - HI0-360 Series |
| S.B. 475B | Crankshaft Gear Modification and Assembly Procedures |
| S.I. 1331A | Crankshaft Gear Replacement- TIO &TIGO-541 Series |
| S.B. 505 | Crankshaft ID, Inspection for Corrosion |
| S.I. 1205 | Crankshaft Journal Diameters, Standards for |
| S.I. 1333 | Crankshaft Listing: Catalog PC-206 |
| S.I. 1020B | Crankshaft Main Bearing Replacement |
| S.I. 1111 | Crankshaft Oil Seal Surface, Recondition of Worn |
| S.I. 1324A | Crankshaft Oil Seals |
| S.B. 300B* | Crankshaft Propeller Flange Inspection (A.D. #65-03-03) |
| S.B. 222C | Crankshaft Renitriding Recommendations |
| S.I. 1044 | Crankshaft Spline Bushing Replacement, Rear |
| S.L. L202B | Crankshaft w/ Lightning Holes, All 320, 360 and 540 Series Engines Using, Installed in Aircraft used for Aerobatic Maneuvers |
| S.I. 1185 | Crankshaft, Interference Between Crankcase and |
| S.I. 1012F | Crankshaft, Proper Assembly Procedure of Counterweights & Rollers |
| S.I. 1130 | Crankshafts, Marking or Identifying |
| S.I. 1106D | Crimping Requirements, Connecting Rod Bolt Nut |
| S.B. 484* | Crossover Exhaust Assembly, Inspection, Alignment and Modification of (AD. #89-12-04) |
| S.I. 1299A | Cushion and Magneto Drive Gear Modification |
| S.B. 334C | Cylinder Assemblies, Replacement |
| S.L. L159D | Cylinder Barrel Repair, Facilities for |
| S.B. 213A | Cylinder Base Allen Head Nuts, Replacing Cylinder Base Spline Nuts with |
| S.B. 213A | Cylinder Base Spline Nuts, Replacing with Cylinder Base Allen Head Nuts |
| S.I. 1191 | Cylinder Compression |
| S.L. L220 | Cylinder Flange Engines, Non-Availability of New Standard |
| S.B. 507 | Cylinder Head Assembly, Missing Spotfaces on P/N 74218 |
| S.L. L228 | Cylinder Head Exhaust Port, Cracking of |
| S.I. 1135A | Cylinder Head Inspection, Repair and Modification |
| S.B. 348A | Cylinder Head, Clearance Between Valve Rocker and |
| S.I. 1228A | Cylinder Hold-Down Plates, Modification of |
| S.B. 520 | Cylinder Kits P/N 05K21108, P/N 05K21118 and P/N 05K21104, Shipped with Incorrect Piston |
| S.I. 1297 | Cylinder Modification for Shroud Tubes with Helical Spring Retention |
| S.B. 271A | Cylinder Painting |
| S.L. L188 | Cylinders Treated with Black Oxide Finish |
| S.I. 1037K | Cylinders, Approved for Use in Textron Lycoming Aircraft Engines |
| S.I. 1181 | Cylinders, Color Code for Avco Lycoming Engines |
| S.I. 1047B | Cylinders, Inspection and Reconditioning Procedures for Nitride Hardened Steel |
| S.I. 1136A | Cylinders, Parallel Valve, Exhaust Valves w/ 1/2" Diameter Stems & Ni-Resist Guides |
| S.I. 1075A | Cylinders, Top Exhaust, Procedure for Removing Push Rods and Shroud Tubes |
| S.I. 1187G | Density Controller Adjustment, Turbocharger |
| S.B. 245D | Detuning, Dynamic Counterweight System |
| S.I. 1446* | Diaphragm, Pressure Regulator, Possible Ruptured, in AN Fuel Pump (A.D. #91-08-07) |
| S.B. 472 | Disassembly of Wide Cylinder Flange Crankcases |
| S.L. L200 | Disclaimer Statement |
| S.L. L226 | Discoloration, LW-16702 Oil Additive |
| S.I. 1344 | Dowel Hole Repair, Propeller Flange |
| S.I. 1298 | Dowel Removal, Engine Mounting |
| S.I. 1225D | Dowel, Crankcase Bearing, Replacement |
| S.I. 1123C | Dowel, Installation of P/N 75302 at Thru-Stud Locations |
| S.I. 1394 | Dowel, Oil Transfer, Modification to Retrofit Hollow, on Accessory Housing & Cover Assy. |
| S.B. 426* | Drain Flange Replacement, Turbocharger Oil (A.D. #80-02-13) |
| S.I. 1399 | Drain Tube Replacement, Turbocharger Oil |
| S.I. 1264 | Drains, Moisture, Addition in Magneto Cover |
| S.I. 1158 | Drive Adapter, Magneto, Replacement |
| S.I. 1144 | Drive Assy. (64894), Use & Maintenance of 4Lug Test, w/ Vertical Test Stand (64765) |
| S.I. 1239 | Drive Assy., Starter, Replacement |
| S.I. 1177B | Drive Bearing Repair, Governor, in Crankcase |
| S.I. 1330A | Drive Coupling, Alternator, Spring Loaded - TIGO-541-E |
| S.I. 1351 | Drive Gear and Drive Shaft, Accessory |
| S.I. 1386A | Drive Gear Bushing, Magneto, Replacement of Damaged or Worn |
| S.I. 1118A | Drive Gear Replacement, Starter |
| S.I. 1387 | Drive Gear, Governor, Replacement of |
| S.I. 1218A | Drive Gear, Integral, Parts Substitution Chart for Camshaft with |
| S.I. 1360 | Drive Gear, Magneto |
| S.I. 1299A | Drive Gear, Magneto, and Cushion Modification |
| S.I. 1242A | Drive Gear, Starter, Thrust Washers for |
| S.I. 1278 | Drive Lubrication, Starter |
| S.I. 1287 | Drive Modification, Starter: Cold Weather Starting |
| S.I. 1376 | Drive Pin Replacement, Starter |
| S.I. 1296 | Drive Plate and Crankshaft Attaching Parts |
| S.I. 1084A | Drive Shaft and Components, Intermediate Supercharger |
| S.I. 1338 | Drive Shaft Modification, Hydraulic Pump |
| S.I. 1145 | Drive Shaft, Accessory, Modification to Incorporate, w/ Larger Spline Drive |
| S.I. 1420 | Drive Spline Lubrication, Fuel Pump |
| S.B. 411 B | Drive, Magneto Isolation, Adapter Kit |
| S.B. 385C* | Drive, Oil Pump Impeller and, Replacement (Refer to Supplement No. 1 to S.B. 385C) (A.D. #75-08-09) |
| S.I. 1203 | Driveshaft Adapter Assembly, Accessory, Installation of Improved |
| S.I. 1221A | Dry Air Pump Drive Oil Seal Replacement |
| S.B. 113 | Dry Sump Test Stand Installation for Lycoming Opposed Series Engines |
| S.L. L172B | EGME, Ethylene Glycol Monomethyl Ether, Fuel Additive |
| S.I. 1276 | Electrical Components, Bendix Bulletin No. 529A, " Torque Values for Drive Shaft Nut " |
| S.L. L114AF | Engine and Accessory Maintenance Publications |
| S.I. 1246 | Engine Conversion for Use of 100/130 Grade Fuel |
| S.L. L193 | Engine Firing Order |
| S.B. 357 | Engine Inspection in Event of Immersion |
| S.I. 1463 | Engine Model TIO-540-AE2A, Improved Controllers |
| S.I. 1408 | Engine Mount Replacement |
| S.I. 1248B | Engine Mounting Bracket Attaching Bolts |
| S.I. 1304G | Engine Nameplate Replacement |
| S.L. L109 | Engine Operation, Suggestions for Better |
| S.L. L142B | Engine Performance, Policy Relative to Alterations |
| S.L. L180A | Engine Preservation for Active and Stored Aircraft |
| S.I. 1241B | Engine Start, Pre-Oiling Prior to Initial |
| S.I. 1287 | Engine Starting, Cold Weather: Starter Drive Modification |
| S.I. 1362 | Engine Starting, Hard |
| S.B. 349 | Engine Starting, Relocating Fuel Drain Valve to Improve |
| S.L. L163C | Engine Stoppage, Recommendations Regarding Accidental |
| S.I. 1427B | Engine Test After Overhaul (w/ Engine Installed in Aircraft) |
| S.I. 1437 | Engine Timing Marks |
| S.I. 1472 | Engine, Removal of Preservative Oil |
| S.L. L202B | Engines Installed in Aircraft Used for Aerobatic Maneuvers, All 320, 360 and 540 Series Using Crankshaft w/ Lightning Holes |
| S.L. L220 | Engines, Non-Availability of New Standard Cylinder Flange |
| S.L. L154B | Engines, Ordering and/or Special Adjustment Consideration for Returned or Run-Out |
| S.B. 484* | Exhaust Assembly, Crossover, Inspection, Alignment and Modification of (A.D. #89-12-04) |
| S.I. 1214A | Exhaust Bypass Valve: Reset for Critical Altitude |
| S.I. 1204B | Exhaust Flange Gaskets |
| S.I. 1363 | Exhaust Manifold Ball Joint and Retaining Strap - TO-360-C1A6D |
| S.I. 1320 | Exhaust Manifold Components, Tightening Procedure |
| S.I. 1410 | Exhaust Manifold Pipe Improvement |
| S.I. 1391 | Exhaust Manifold Tube Alignment |
| S.I. 1190 | Exhaust Manifold Tube Modification |
| S.B. 499B* | Exhaust Pipe Kit (05K21503), One-Piece, Installation of (A.D. #91-21-01) |
| S.B. 479 | Exhaust Pipe, Inspection of P/N 77429 Right Intermediate, and Exhaust Slip Joint Modification |
| S.L. L228 | Exhaust Port, Cracking of Cylinder Head |
| S.B. 393C | Exhaust Slip Joint Modification - TIGO-541-E Series |
| S.B. 479 | Exhaust Slip Joint Modification and Inspection of P/N 77429 Right Intermediate Exhaust Pipe - TIO-541-E Series |
| S.B. 435* | Exhaust Spring Seat, Upper, Replacement of Hydraulic Lifter and (Refer to Supplement No. 1 and 2 to S.B. 435) (A.D. #80-04-03) |
| S.I. 1422 | Exhaust System Inspection (EGT Probe Depth) |
| S.B. 491A* | Exhaust Transition Bolts, Inspection of (A.D. #91-10-04) |
| S.B. 388B | Exhaust Valve and Guide, Procedure to Determine Condition |
| S.I. 1342 | Exhaust Valve Guide Clearance, Increased |
| S.B. 503 | Exhaust Valve Guide Replacement on TIO-540-AF1 A Engines |
| S.I. 1200A | Exhaust Valve Guide, Honing During Replacement |
| S.B. 490A | Exhaust Valve Guides, and Intake, Installation of |
| S.B. 293B* | Exhaust Valve Guides, Inspection of (A.D. #63-23-02) |
| S.B. 404 | Exhaust Valve Inspection (High Lead Fuel Operation) |
| S.I. 1430 | Exhaust Valve Replacement - All w/ P/N 73111 Exhaust Valves |
| S.B. 419 | Exhaust Valve Replacement - TO-360 |
| S.I. 1268B | Exhaust Valve Rocker Assy. |
| S.I. 1468 | Exhaust Valve Rocker Assy. |
| S.I. 1381 | Exhaust Valve Spring Seat, Upper, and Hydraulic Lifter, Replacement |
| S.B. 447A* | Exhaust Valve Spring Seats, Inspection (A.D. #80-14-07) |
| S.I. 1116C | Exhaust Valve to Guide Clearance Modification |
| S.L. L213A | Extension Kit, Time Between Overhaul (TBO) |
| S.I. 1355 | Extensions and Clamps, Intake Pipe |
| S.I. 1354B | Face Repair, Crankcase Thrust |
| S.B. 481 | Facet Aerospace Products Service Bulletin NO A1-87, " Carburetor Return and Inspection " |
| S.B. 483 | Facet Aerospace Products Service Bulletin No. A1-88, " Possible Loose 62-226 Pins " |
| S.L. L159D | Facilities for Cylinder Barrel Repair |
| S.L. L206A | Field-Reconditioned Tappet Bodies/Cam Followers |
| S.I. 1169C | Filter Assy., Oil, Inspection and Replacement |
| S.B. 466 | Filter Base Adapter, Oil, Inspection |
| S.B. 480 | Filter Change, and Oil, and Cleaning |
| S.B. 337A | Filter Housing, Oil, and Bolt Modification |
| S.I. 1457 | Filter Kit, Remote Mount Oil, Textron Lycoming |
| S.L. L183 | Filter Lubricants, Spin-On |
| S.I. 1186 | Filter Screen, Removal from Fuel Injector Nozzle |
| S.I. 1002 | Filters, Carburetor Air, Proper Maintenance |
| S.I. 1109 | Filters, Fuel and Oil, Procedure for Cleaning Simmonds Fuel Injector |
| S.I. 1079B | Filters, Fuel Line Servo, Periodic Maintenance |
| S.B. 431 | Fire Sleeve, Teflon Fuel Hoses with |
| S.L. L193 | Firing Order, Engines |
| S.I. 1062 | Fitting, ITS, Maintenance Procedures for the Fuel Vent Return |
| S.B. 494* | Fittings, Restricted Fuel Pump Vent, Installation of (A.D. #91-08-07) |
| S.B. 497* | Fittings, Restricted Fuel Pump Vent, New, Installation in AN Drive (A.D. #91-08-07) |
| S.I. 1435 | Fixed Pitch to Constant Speed Propeller Conversion, and Vice Versa (Refer to Supplement No. 1 to S.I. 1435) |
| S.B. 482 | Flange Area, Cracking, Crankshaft |
| S.I. 1209B* | Flange Bolt Replacement, Crankshaft (A.D. #80-04-04) |
| S.I. 1098E | Flange Bushing Location, Propeller |
| S.I. 1452 | Flange Bushings, Propeller, Reindexing (0-360-C1G) |
| S.B. 253A | Flange Bushings, Replacement of Propeller |
| S.I. 1344 | Flange Dowel Hole Repair, Propeller |
| S.I. 1204B | Flange Gaskets, Exhaust |
| S.B. 512 | Flange Joint, Marmon, Inspection at Transition Inlet |
| S.B. 426* | Flange Replacement, Turbocharger Oil Drain (A.D. #80-02-13) |
| S.B. 465C* | Flange, Crankshaft, Inspection for Aerobatic Engines (A.D. #84-13-05) |
| S.B. 300B* | Flange, Inspection of Crankshaft Propeller (A.D. #65-03-03) |
| S.I. 1345 | Flange, Narrow Cylinder, Service Replacement Crankcases for Four Cylinder Engines |
| S.B. 201 E | Flanges, Inspection & Straightening of Bent Crankshaft |
| S.I. 1206 | Float, Carburetor, Checking Clearance |
| S.L. L192B | Fouling, Spark Plug |
| S.I. 1112E | Fretted Crankcases, Repair of (Refer to Supplement No. 1 to S.l. 1112E) |
| S.B. 439A | Fretting, Inspection and Repair of Connecting Rod |
| S.L. L190 | Fuel Additive, Use of " TCP " |
| S.L. L172B | Fuel Additive, Use of Ethylene Glycol Monomethyl Ether (EGME) such as " Prist " |
| S.B. 384 | Fuel Drain Check Valve Modification |
| S.B. 349 | Fuel Drain Valve, Relocating to Improve Engine Starting |
| S.I. 1109 | Fuel Filters, Procedures for Cleaning Simmonds Fuel Injector |
| S.I. 1069A | Fuel Flow, Procedure for Inspection & Adjustment to Regulate, on Simmonds Model No. 580 Fuel Injector |
| S.I. 1274B | Fuel Hoses, Silicone Coated, Service Replacement |
| S.B. 431 | Fuel Hoses, Teflon with Fire Sleeve |
| S.L. L204 | Fuel Injection Conversion Kit P/N LW-18866 |
| S.I. 1455 | Fuel Injection Manifold Kit P/N 05K21433, Installation |
| S.I. 1072 | Fuel Injection Nozzles for Simmonds No. 530 Fuel Injection System |
| S.I. 1040A | Fuel Injection System, Simmonds No. 530, Maintenance Procedures |
| S.I. 1211 D | Fuel Injector and Controller Linkage Setting |
| S.I. 1301 A | Fuel Injector Lines, Identification |
| S.B. 331 | Fuel Injector Lines, Inspection and Removal of Rubber Sleeve |
| S.I. 1026 | Fuel Injector Mixture Control Installation Procedure, Simmonds Model 580 |
| S.B. 510 | Fuel Injector Nozzle Assys., Recall, Precision Airmotive Corp. Bulletin No. PRS-101 (Refer to Supplement No. 1 to S.B. 510) |
| S.I. 1186 | Fuel Injector Nozzle, Removal of Filter Screen |
| S.I. 1257E | Fuel Injector Nozzles, Cleaning |
| S.I. 1231 | Fuel Injector Nozzles, Torque Requirement - TIO & TIGO-541 Series |
| S.B. 305B* | Fuel Injector Bendix Bulletin No. 18, Rev. 4, " Replacement of Fuel Diaphragm Assy. "(A.D. #67-22-06) |
| S.I. 1166A | Fuel Injector Bendix Bulletin No. 20, Rev. 2, " Identifying Fuel to Air Seal Leak " |
| S.I. 1244 | Fuel Injector, Bendix Bulletin No. RS-35, " Changes - Regulator & Fuel Control System " |
| S.I. 1247 | Fuel Injector, Bendix Bulletin No. RS-37, " Replacement of Idle Valve Lever Assy. " |
| S.B. 382* | Fuel Injector, Bendix Bulletin No. RS-43, " Inspection and Modification of Flow Dividers " (A.D. #75-09-15) |
| S.B. 428* | Fuel Injector, Bendix Bulletin No. RS-52, " Mod. of RSA-5AB1, RSA-5AD1 & RSA-1OAD1 " (Refer to Supplement No. 1 to S.B. 428) (A.D. #78-23-10) |
| S.B. 429* | Fuel Injector Bendix Bulletin No. RS-53, " Modification of RSA-7AA1 " (A.D. #78-23-10) |
| S.B. 430* | Fuel Injector Bendix Bulletin No. RS-54, " Mod. of RSA-10DB1, RSA-1ODB2 & RSA-1OED1 " (Refer to Supplement No. 1 to S.B. 430) (AD #78-23-10) |
| S.B. 433A* | Fuel Injector, Bendix Bulletin No. RS-57, Rev. 1, " Inspection of Fuel Diaphragm Assy. P/N 2529471 " (A.D. #79-04-05) |
| S.B. 444A* | Fuel Injector, Bendix Bulletin No. RS-62, Rev. 2, " Modification of Mixture Control Shaft Assy ." (A.D. #81-03-05) |
| S.B. 445 | Fuel Injector, Bendix Bulletin No. RS-63, " Inspection of Fuel Diaphragm Assy. " |
| S.B. 441 | Fuel Injector, Bendix Bulletin No. RS-66, " Modification of Idle Valve Assy. " |
| S.B. 442* | Fuel Injector, Bendix Bulletin No. RS-68, " Integrity Inspection of Regulator Stem Nut " (Refer to Supplement No. 1 to S.B. 442) (A.D. #'s 79-21-08, 79-26-03) |
| S.B. 443* | Fuel Injector, Bendix Bulletin No. RS-69, " Integrity Inspection of Regulator Stem Nut " (A.D. #79-21-08) |
| S.I. 1414A | Fuel Injector, Bendix Bulletin No. RS-77, Rev. 1, " Air Bleed Nozzle, RS & RSA Fuel Injection Systems, Two Piece Assy. " |
| S.B. 467* | Fuel Injector, Bendix Bulletin No. RS-88, " Deter. of Fuel Diaphragm Change " (Refer to Supplements No. 1 & 2 to S.B. 467) (A.D. #83-22-04) |
| S.I. 1404A | Fuel Injector, Bendix Bulletin No. SSB-318, " Overhaul Periods for Bendix Fuel System Components " |
| S.I. 1335 | Fuel Injector, Bendix Letter No. 22, " Mixture Control Maintenance " |
| S.I. 1445 | Fuel Injector, Precision Airmotive Corp. Service Bulletin No. PAS-91, " Timing of the Power Enrichment Valve Opening " |
| S.B. 485* | Fuel Injector, Precision Airmotive Corp. Service Bulletin No. PAS-92, " Contamination " (A.D. #89-13-02) |
| S.I. 1069A | Fuel Injector, Simmonds Model No. 580, " Proc. for Inspection & Adjustment to Regulate Fuel Flow " |
| S.I. 1378 | Fuel Injectors and Carburetors, Overheating, Bendix Fuel Injector Bulletin No. SSB-317 (Preheating Procedures) |
| S.L. L150T | Fuel Injectors, Simmonds, Reconditioned |
| S.B. 342B* | Fuel Line and Support Clamp Inspection and Installation (A.D. #92-12-10) |
| S.B. 421* | Fuel Line Between Fuel Pump and Fuel Injector (IO-540-G1B5, -K1F5, -P1A5, -S1A5) (A.D. #78-23-08) |
| S.I. 1079B | Fuel Line Filters, Servo, Periodic Maintenance |
| S.I. 1431 | Fuel Metering and Turbocharger Linkage Adjustments (Refer to Supplement No. 1 to S.l. 1431) |
| S.L. L221 | Fuel Metering Components, Bendix, Warranty Repair of |
| S.I. 1094D | Fuel Mixture Leaning Procedure |
| S.I. 1446* | Fuel Pump (AN), Possible Ruptured Pressure Regulator Diaphragm (A.D. #91-08-07) |
| S.L. L218 | Fuel Pump Adapters |
| S.I. 1420 | Fuel Pump Drive Spline Lubrication |
| S.B. 374 | Fuel Pump Inlet Inspection |
| S.B. 406 | Fuel Pump Inspection, Romec and Titan |
| S.I. 1309 | Fuel Pump Modification, Lear Siegler |
| S.B. 497* | Fuel Pump Vent Fittings, New, Restricted, Installation in AN Drive (A.D. #91-08-07) |
| S.B. 494* | Fuel Pump Vent Fittings, Restricted, Installation of (A.D. #91-08-07) |
| S.B. 487* | Fuel Pump Vent Restriction (A.D. #89- 15- 10) |
| S.B. 496 | Fuel Pump, Lear Romec Service Bulletin No. 101SB019, " Relief Valve Diaphragm Replacement " |
| S.B. 500A | Fuel Pump, Lear Romec Service Bulletin No. 3402, " Rotary Fuel Pump - Non-Conforming Regulating Valve Diaphragm " |
| S.B. 506 | Fuel Pump, Lear Romec Service Bulletin No. 3403, " Rotary Fuel Pump - Replacement of Regulator Valve Diaphragm " |
| S.I. 1110C | Fuel Pumps, AC, Replacement |
| S.B. 362A | Fuel Vent Line Check Valve Installation |
| S.I. 1062 | Fuel Vent Return, T Fitting, Maintenance Procedures |
| S.I. 1246 | Fuel, Engine Conversion for Use of 100/130 Grade Fuel |
| S.L. L185B | Fuel, Higher Octane Aviation, Use of 100LL for Engines Rated 80/87 Octane |
| S.L. L199 | Fuel, Recommendations Regarding Use of |
| S.B. 398 | Fuel, Recommendations Regarding Use of Incorrect |
| S.I. 1070K | Fuels, Specified |
| S.B. 407A* | Gage Assys., Oil Level (A.D. #77-07-07) |
| S.I. 1379 | Gage Kit, Oil Level |
| S.I. 1288 | Gage, Oil Level, Modification of |
| S.B. 451 | Gage, Oil Level, Rework or Replacement |
| S.B. 439A | Galling, Inspection of Connecting Rod for |
| S.I. 1453 | Gasket, Oil Filter Converter Plate, Replacement of |
| S.I. 1204B | Gaskets, Exhaust Flange |
| S.I. 1016C | Gear and Camshaft Replacement |
| S.I. 1439 | Gear Assembly and Camshaft, New Integral, Installation (Refer to Supplement NO 1 to S.l. 1439) |
| S.B. 475B | Gear Assembly Procedures and Modification, Crankshaft |
| S.B. 319B* | Gear Assy., Inspection, Reduction (A.D. #69-25-08) |
| S.I. 1076 | Gear Assys., Bevel, Pitch Alignment and Backlash |
| S.I. 1196 | Gear Attaching Studs, Reduction, Replacement |
| S.I. 1386A | Gear Bushing, Magneto Drive, Replacement of Damaged or Worn |
| S.I. 1159 | Gear Housing Interference, Reduction, Crankcase Modification to Prevent |
| S.B. 178A | Gear Housing Sleeve, Repair of Worn Reduction |
| S.B. 475B | Gear Modification and Assembly Procedures, Crankshaft |
| S.I. 1236A | Gear Pinion Cages, Reduction, Repair Procedure for Worn (Refer to Supplement NO 1 to S.l. 1236A) |
| S.I. 1331A | Gear Replacement, Crankshaft - TIO & TIGO-541 Series |
| S.I. 1417 | Gear Shaft Bore Repair, Crankcase |
| S.I. 1197A | Gear Shaft Recesses, Idler, Repair |
| S.B. 486 | Gear Support Assemblies, Inspection of Single Belt Driven Starter Ring |
| S.I. 1351 | Gear, Drive, and Drive Shaft, Accessory |
| S.I. 1387 | Gear, Governor Drive, Replacement of |
| S.I. 1360 | Gear, Magneto Drive |
| S.I. 1356 | Gear, Reduction, Oversize Thrust Bearing for |
| S.L. L233 | Gear, Ring, Support Assys., Better Identification of Reverse Rotation |
| S.I. 1118A | Gear, Starter Drive, Replacement |
| S.I. 1121 | Gears, Ring, Identification |
| S.I. 1141 | Gears, Starter Ring, Replacement of Worn |
| S.I. 1170 | Generator Mounting Bolt Replacement |
| S.I. 1129A | Generator, DC, Methods of Checking, and Alternator Belt Tension |
| S.I. 1105A | Generator/Alternator Mounting Brackets, Periodic Inspection |
| S.I. 1154E | Generators, FAA Approved |
| S.B. 246 | GO-435-C2B and -C2B2 Conversion to GO-435-C2B-6 and -C2B2-6 |
| S.I. 1177B | Governor Drive Bearing Repair in Crankcase |
| S.I. 1387 | Governor Drive Gear, Replacement of |
| S.B. 488A* | Governor Line Support, Propeller (Refer to Supplement No. 1 to S.B. 488A) (A.D. #90-04-06) |
| S.I. 1438 | Governor Pad Plate, Propeller, P/N LW-12347 |
| S.B. 364A* | Grommet, Magneto Replacement (A.D. #73-15-04) |
| S.I. 1266 | Ground Strap, Alternator - All Engines with Prestolite |
| S.I. 1342 | Guide Clearance, Exhaust Valve, Increased |
| S.B. 503 | Guide Replacement, Exhaust Valve on TIO-540-AFlA Engines |
| S.I. 1116C | Guide, Exhaust Valve Clearance Modification |
| S.I. 1200A | Guide, Exhaust Valve, Honing During Replacement |
| S.I. 1136A | Guides, Ni-Resist, in Parallel Valve Cylinders |
| S.I. 1256E | Guides, Valve, for Service Use |
| S.B. 490A | Guides, Valve, Installation of Intake and Exhaust |
| S.I. 1362 | Hard Starting |
| S.I. 1419 | Harness, Magneto Wiring, Modification of |
| S.I. 1227 | Hartzell Propeller Letter No. 17, " Oil Leakage. " |
| S.I. 1148B | Heat Control, Use of Carburetor |
| S.I. 1448 | Heater MumerCovers, Installation of Tailpipes and (Refer to Supplement Nos. 1 and 2 to S.l. 1448) |
| S.I. 1043A | Heli-Coil Insert Replacement, Spark Plug |
| S.B. 387 | Heli-Coil Installation in Induction Housing |
| S.L. L162B | Heli-Coil Service Repair Kit |
| S.I. 1297 | Helical Spring Retention, Cylinder Modification for Shroud Tubes with |
| S.I. 1291 | High Altitude Operation, ignition System for |
| S.B. 404 | High Lead Fuel Operation, Exhaust Valve, Inspection |
| S.I. 1432A | High-Crush, Thin-Wall Rear Main Bearings, Installation of in Crankcases without Retention Dowels |
| S.I. 1469 | High-Tensile Strength Bolt, Connecting Rod with |
| S.I. 1323A | High-Tensile Strength Bolts, Connecting Rods with |
| S.L. L185B | Higher Octane Aviation Fuel, Use of 100LL for Engines Rated 80/87 Octane |
| S.I. 1350A | HI0-360-D1A, Redesigned Camshaft |
| S.I. 1228A | Hold-Down Plates, Cylinder, Modification of |
| S.I. 1257E | Horsepower, Manifold Pressure and RPM Values |
| S.B. 509 | Hose Assemblies, 601, Aeroquip Service Bulletin No. AA135 |
| S.I. 1361 | Hose Clamps, T-Bolt |
| S.I. 1464 | Hose Line Problems, Aeroquip Service Bulletin No. AA91 |
| S.I. 1274B | Hoses, Fuel and Oil, Silicone Coated, Service Replacement |
| S.I. 1234 | Housing Assy., Induction, Tightening Procedure |
| S.B. 417 | Housing, Air Inlet |
| S.I. 1396 | Housing, Induction Air, Redesigned |
| S.I. 1171 | Housings, Accessory, and Covers, Salvage of |
| S.I. 1286B | Housings, Stainless Steel, TE0659 Turbochargers with |
| S.I. 1011G* | Hydraulic Lifter Assy., Plunger Assys., Tappet Bodies: Table of Current and Inspection Procedures (AD. #62-03-02) |
| S.I. 1352A | Hydraulic Lifter Body Disassembly |
| S.I. 1406B | Hydraulic Lifters, Crankcases with Provision for Large-Diameter |
| S.I. 1402 | Hydraulic Lifters, Redesigned |
| S.I. 1338 | Hydraulic Pump Drive Shaft Modification |
| S.B. 238 | Hydraulic Tappet Plunger Assys., Magnetized Condition |
| S.B. 424* | Hydraulic Tappet Replacement (AD. #77-20-07) |
| S.I. 1424 | Hydraulic Tappet/Plunger Assy. P/N 78290, Installation Procedure |
| S.I. 1390 | Idle Tube, Carburetor, Replacement |
| S.I. 1197A | Idler Gear Shaft Recesses, Repair |
| S.I. 1341 | Idler Shaft Lubrication, Oil Pump |
| S.I. 1343A | Idler Shaft, Propeller Governor, Set Screw for |
| S.I. 1310A | Idler Shafts, Lockwire for |
| S.I. 1294 | Ignition Cable Routing, Alternate |
| S.L. L222 | Ignition Components, Teledyne Continental Motors, Warranty Repair |
| S.I. 1365 | Ignition Harness Spark Plug Ends, Bendix Electrical Bulletin No. 597, Cleaning of |
| S.I. 1314 | Ignition Leads (Slick) Furnish on Bendix Magnetos, Replacement |
| S.I. 1375 | Ignition Noise, Bendix Electrical Components Bulletin No. 603 |
| S.I. 1291 | Ignition System for High Altitude Operation |
| S.B. 357 | Immersion, Engine Inspection in Event of |
| S.B. 385C* | Impeller and Drive Replacement, Oil Pump (Refer to Supplement No. 1 to S.B. 385C) (A.D. #75-08-09) |
| S.B. 381C* | Impeller and Oil Pump Woodruff Key Drive Replacement (AD. #75-08-09) |
| S.I. 1032G | Impeller Assys., Supercharger, Parts Replacement and Dynamic Balance |
| S.B. 423* | Impeller Replacement and Oil Pump Inspection (AD. #78-12-08) |
| S.I. 1230B | Impellers, Oil Pump |
| S.I. 1434 | Impellers, Oil Pump, Improved |
| S.B. 454B* | Impellers, Replacement of Oil Pump - Hl0-360 (AD. #81-18-04) |
| S.B. 455D* | Impellers, Replacement of Oil Pump - O. IO, TO-360 (A.D. #81-18-04) |
| S.B. 456F* | Impellers, Replacement of Sintered Iron Oil Pump (AD. #81-18-04) |
| S.I. 1189 | Impulse Coupling Magneto, Slick Malfunction |
| S.B. 508 | Impulse Coupling, Proper Installation, Teledyne Continental Motors Service Bulletin No. 639 |
| S.I. 1396 | Induction Air Housing, Redesigned |
| S.I. 1234 | Induction Housing Assy., Tightening Procedures |
| S.B. 387 | Induction Housing, Heli-Coil Installation |
| S.L. L204 | Injection Conversion Kit P/N LW-18866, Fuel |
| S.I. 1407 | Injection Pumps, Simmonds Precision Bulletin No. V-1164, " Periodic Inspection & Overhaul " |
| S.I. 1301A | Injector Lines, Fuel, Identification |
| S.I. 1275B | Injector Nozzles, Fuel, Cleaning |
| S.B. 421* | Injector, Fuel Line Between Fuel Pump and Fuel (A.D. #78-23-08) |
| S.I. 1329A | Inlet Adapter Seals, Supercharger |
| S.I. 1300 | Inlet Oil Pressure, Increased Turbocharger |
| S.B. 477A* | Inspection and Rework of P/N LW-18790 Rocker Arm Assy. (Refer to Supplement No. 1 to S.B. (A.D. #87-10-06) |
| S.B. 505 | Inspection of Crankshaft ID for Corrosion |
| S.B. 479 | Inspection of P/N 77429 Right Intermediate Exhaust Pipe and Exhaust Slip Joint Modification |
| S.B. 486 | Inspection of Single Belt Driven Starter Ring Gear Support Assemblies |
| S.B. 484* | Inspection, Alignment and Modification of Crossover Exhaust Assembly (A.D. #89-12-04) |
| S.I. 1216 | Intake Pipe and Seal Replacement |
| S.I. 1168B | Intake Pipe Bores, Repair, Oil Sump |
| S.I. 1355 | Intake Pipe Extensions and Clamps |
| S.I. 1173 | Intake Pipe Mounting Stud Replacement |
| S.B. 490A | Intake Valve Guides, and Exhaust, Installation of |
| S.L. L181 | Intake Valve Replacement (See Service Instruction Nos. 1280C, 1262A & 1302A) |
| S.I. 1302A | Intake Valve, Rotator, with Small Diameter Head |
| S.B. 502 | Intake Valves, P/N LW-13262, Replacement, Etched With Date Code K-L |
| S.I. 1280C | Intake Valves, Rotator Type |
| S.I. 1262A | Intake Valves, Small Head, and Venturi Seats |
| S.I. 1439 | Integral Camshaft and Gear Assembly, Installation of New (Refer to Supplement No. 1 to S.l. 1439) |
| S.I. 1397 | Inverted Oil System, Overflow Oil from Breather Fitting |
| S.I. 1263B | IO-360 Series Engines, Redesigned Camshaft |
| S.I. 1325A | IO-360 Series Engines, Timing Change |
| S.B. 302A* | IO-360-A1A Engines, Replacement of P/N's 74308 & 74503 Connecting Rod Assys. (A.D. #66-06-03) |
| S.B. 380A | IO-360-C Timing Change |
| S.I. 1436 | Isolation Drive, Magneto, Adapter Kit for |
| S.I. 1205 | Journal Diameters, Standards for Crankshaft |
| S.B. 411 B | Kit, Adapter, for Magneto Isolation Drive |
| S.I. 1393 | Kit, Carburetor Modification |
| S.L. L162B | Kit, Heli-Coil Service Repair |
| S.I. 1455 | Kit, P/N 05K21433, Fuel Injection Manifold, Installation |
| S.B. 520 | Kits, Cylinder P/N 05K21108, P/N 05K21118 and P/N 05K21104, Shipped with Incorrect Piston |
| S.B. 371 A* | Kits, New Rods w/High Crush Bearings, Connecting Rod Assys. (A.D. #73-05-01) |
| S.I. 1314 | Leads, ignition (Slick) Furnished on Bendix Magnetos, Replacement |
| S.I. 1462 | Leak Test Procedure, Propeller Oil Control |
| S.I. 1094D | Leaning Procedures, Fuel Mixture |
| S.B. 496 | Lear Romec Service Bulletin No. 101SB019, Fuel Pump, " Relief Valve Diaphragm Replacement " |
| S.B. 500A | Lear Romec Service Bulletin No. 3402, Fuel Pump, " Rotary Fuel Pump - Non-Conforming Regulating Valve Diaphragm " |
| S.B. 506 | Lear Romec Service Bulletin No. 3403, Fuel Pump, " Rotary Fuel Pump - Replacement of Regulator Valve Diaphragm " |
| S.I. 1309 | Lear Siegler Fuel Pump Modification |
| S.I. 1379 | Level Gage Kit, Oil |
| S.I. 1288 | Level Gage, Oil, Modification of |
| S.I. 1265A | Lever, Serrated Throttle, and Shaft |
| S.I. 1352A | Lifter Body Disassembly, Hydraulic |
| S.I. 1381 | Lifter, Hydraulic, and Upper Exhaust Valve Spring Seat, Replacement |
| S.I. 1402 | Lifter, Hydraulic, Redesigned |
| S.B. 435* | Lifter, Hydraulic, Replacement of Upper Exhaust Valve Spring and (Refer to Supplement Nos. 1 and 2 to S.B. 435) (A.D. #80-04-03) |
| S.I. 1406B | Lifters, Hydraulic, Crankcases with Provisions for Large-Diameter |
| S.I. 1011G* | Lifters, Hydraulic, Inspection Procedures & Table of Current (A.D. #62-03-02) |
| S.L. L202B | Lightning Holes, All 320, 360 and 540 Series Engines using Crankshaft with, Installed in Aircraft Used for Aerobatic Maneuvers |
| S.B. 401 | Lightning, Recommendations for Aircraft Struck by |
| S.I. 1447B | Lightweight Starter Installation Instructions |
| S.I. 1461 | Lightweight Starter P/N 31B21064 (24V) and P/N 31A21198 (12V), Improved Pinion |
| S.B. 314C* | Limited Travel Valve Lifter Replacement (A.D. #68-08-08) |
| S.I. 1124B | Limits, Oil Consumption Test |
| S.B. 488A* | Line Support, Propeller Governor (Refer to Supplement No. 1 to S.B. 488A) (A.D. #90-04-06) |
| S.I. 1211D | Linkage, Controller, and Fuel Injector Setting |
| S.I. 1431 | Linkage, Turbocharger, and Fuel Metering Adjustments (Refer to Supplement No. 1 to S.l. 1431) |
| S.L. L147B | Lubricant, Anderol 471 All-Climate Synthetic Aircraft |
| S.L. L183 | Lubricants, Spin-On Filter |
| S.B. 318B | Lubricating Oil Limitations |
| S.L. L203 | Lubricating Oil Recommendations |
| S.I. 1014K | Lubricating Oil Recommendations |
| S.I. 1392 | Lubricating Oil Recommendations and Cold Weather Operation |
| S.B. 399 | Lubricating Oil, Safe Quantity |
| S.L. L229A | Lubricating Oil, Use of Mobil AV 1 Synthetic, in Textron Lycoming Reciprocating Engines |
| S.I. 1292A | Lubrication and Stainless Steel Thrust Bearing Modifications |
| S.B. 403 | Lubrication Requirements, Aerobatic Engines |
| S.I. 1420 | Lubrication, Fuel Pump Drive Spline |
| S.I. 1250 | Lubrication, Propeller Shaft Bearing |
| S.I. 1278 | Lubrication, Starter Drive |
| S.I. 1285A | Magnetic Particle Inspection |
| S.I. 1140 | Magneto Bearing Recess, Crankcase, Salvage Repair |
| S.B. 365 | Magneto Conversion, Bendix, to Incorporate Flexible Drive |
| S.I. 1264 | Magneto Cover, Addition of Moisture Drains |
| S.I. 1158 | Magneto Drive Adapter Replacement |
| S.I. 1360 | Magneto Drive Gear |
| S.I. 1299A | Magneto Drive Gear and Cushion Modification |
| S.I. 1386A | Magneto Drive Gear Bushing, Replacement of Damaged or Worn |
| S.B. 311 | Magneto Drive Gears, Inspection and Replacement |
| S.I. 1132A | Magneto Drop-Off |
| S.B. 364A* | Magneto Grommet Replacement (A.D. #73-15-04) |
| S.I. 1252C | Magneto Installation, Bendix 1200 Series |
| S.B. 411 B | Magneto Isolation Drive, Adapter Kit |
| S.I. 1436 | Magneto Isolation Drive, Adapter Kit for |
| S.I. 1224 | Magneto Modification, VO-435-B1A |
| S.I. 1308C | Magneto Pressure Test, Pressurized |
| S.L. L177A | Magneto Replacement Policy, Slick Electro |
| S.I. 1208 | Magneto Shaft Bore Bushings, Installation of |
| S.B. 380A | Magneto Timing Change, IO-360-C Engines |
| S.B. 183A | Magneto Timing Discrepancies |
| S.I. 1419 | Magneto Wiring Harness, Modification of |
| S.B. 340 | Magneto, Bendix Bulletin No. 530A, " Securing Coil Clamp " |
| S.I. 1260 | Magneto, Bendix Bulletin No. 533A, " Acceptable Stress Relief Fissures, Flow Lines and Cracks " |
| S.I. 1226 | Magneto, Bendix Bulletin No. 545, " Tubing for S-1200 Cover Hold Down Screw " |
| S.B. 341 | Magneto, Bendix Bulletin No. 549, " Locating Shoulder for Carbon Brush Spring " |
| S.B. 343B | Magneto, Bendix Bulletin No. 551A, " New Distributor Block Lubricant " |
| S.B. 376* | Magneto, Bendix Bulletin No. 556B, " Magneto Drive Shaft Bushing Change " (A.D. #74-26-09) |
| S.I. 1282 | Magneto, Bendix Bulletin No. 560, " Repl. of Transformer Coils & Rotating Magnets " |
| S.B. 373 | Magneto, Bendix Bulletin No. 566, " S-1200 Dist. Block and Gear Change " (Refer to Supplement No. 1 to S.B. 373) |
| S.I. 1332 | Magneto, Bendix Bulletin No. 573, " Green Block Distributor " |
| S.I. 1327 | Magneto, Bendix Bulletin No. 580, " Breaker Securing Screws " |
| S.B. 416A* | Magneto, Bendix Bulletin No. 584A, " Coil Retaining Devices, D2000/D2200 Mags " (A.D. #78-18-04) |
| S.B. 410* | Magneto, Bendix Bulletin No. 587, " Insp. of D2000 Capacitors & Lead Crimp Terminals " (A.D. #78-18-04) |
| S.I. 1367 | Magneto, Bendix Bulletin No. 588, " Stress Lines in Distributor Blocks " |
| S.B. 414* | Magneto, Bendix Bulletin No. 589, " Rear Bearing Lubrication - D2000/D2200 Mags " (A D. #77- 17-07) |
| S.B. 415A* | Magneto, Bendix Bulletin No. 590A, " Rotating Magnetos to Housing Clearance - D2000/D2200 Mags " (A D. #78-18-04) |
| S.I. 1382 | Magneto, Bendix Bulletin No. 592, " Insp. of Breaker Contact Assys. and Capacitor Flag Terminal Crimps. " |
| S.B. 427A | Magneto, Bendix Bulletin No. 600, " 10-353110 Bearing in D2000/D2200 Mags " |
| S.B. 438A* | Magneto, Bendix Bulletin No. 605A, " Housing Distortion and Coil Retention " (A.D. #80-17- 14) |
| S.B. 437* | Magneto, Bendix Bulletin No. 606, " D2000/D2200 Mags Using Green Distributor Blocks " (A.D. #79-12-07) |
| S.I. 1400 | Magneto, Bendix Bulletin No. 608, " Self-Locking Cam Retaining Screws " |
| S.B. 458 | Magneto, Bendix Bulletin No. 613, " Insp. and/or Repl. of Green Distributor Blocks " |
| S.B. 461 | Magneto, Bendix Bulletin No. 617, " Repl. or Insp. of Distributor Blocks " |
| S.B. 459* | Magneto, Bendix Bulletin No. 618, " Repl. or Insp. of Distributor Blocks " (A.D. #81-12-06) |
| S.B. 460 | Magneto, Bendix Bulletin No. 619, " Repl. or Insp. of Distributor Blocks " |
| S.B. 464A* | Magneto, Bendix Bulletin No. 623A, " Insp. of Impulse Coupling Cam Assys. " (A.D. #82-2aO1) |
| S.L. L207 | Magneto, Bendix Bulletin No. 625, " Broken Coil Securing Clamps, P/N 10-50765 " |
| S.I. 1433 | Magneto, Bendix Bulletin No. 626, " Installation of Impulse Coupling Assemblies " |
| S.B. 469 | Magneto, Bendix Bulletin No. 627, " Distributor Block Kit P/N 10-682056 (6 cylinder) Dual Magneto Series " |
| S.B. 470 | Magneto, Bendix Bulletin No. 628, " Replacement of Impulse Coupling Main Spring P/N IO-382941 " |
| S.B. 474 | Magneto, Bendix Bulletin No. 629, " Insp. & Repl. of Brown Magneto Blocks on Turbocharged (6 cylinder) Engines " |
| S.I. 1120 | Magneto, Scintilla Bulletin No. 502, " S-700 Magnetos - Internal Timing " |
| S.I. 1126 | Magneto, Scintilla Bulletin No. 503, " Lubrication of Tapered Drive on S Series Magnetos " |
| S.I. 1139 | Magneto, Scintilla Bulletins No. 510, " Distributor Gears - S-600 Series and No. 511, Replaceable Electrode - S-700 Series " |
| S.B. 432* | Magneto, Slick Electro Bulletin No. 1-78, " Magneto/Condenser Replacement (A.D. #78-25-01) " |
| S.I. 1385 | Magneto, Slick Electro Bulletin No. 1-79, " Grounding of Non-lmpulse Magnetos (From 4000, 4100 to 4200 Series) " |
| S.B. 449* | Magneto, Slick Electro Bulletin No. 1-80, " Impulse Coupling Hubs " (A D. #80-06-05) |
| S.B. 457A | Magneto, Slick Electro Bulletin No. 1-81, " Magneto Malfunction Due to Cracking of Coil Potting Compound " |
| S.B. 478A | Magneto, Slick Electro Bulletin No. 1-86, " Impulse Coupling Inspections " |
| S.L. L173B | Magneto, Slick Electro Bulletin No. 2-80, " Recommended Maintenance & Inspection " |
| S.B. 468B | Magneto, Slick Electro Bulletin No. 7-83A, " Magneto Bearing Inspection " |
| S.L. L210 | Magneto, Slick Electro Bulletin No. SB1-85, " Impulse Coupling Hub Assembly Replacement Program " |
| S.I. 1357A | Magneto, Slick Electro Instructions No. 1-77, " Lag Angle Inspection " and No. 2-77, " Improved Performance " |
| S.I. 1189 | Magneto, Slick Impulse Coupling, Malfunction |
| S.B. 425B * | Magneto, Teledyne Continental Motors Bulletin No. 599D, " Insp. & Repl. of Impulse Coupling and Stop Pins " (A D. #78-09-07) |
| S.I. 1444 | Magneto, Teledyne Continental Motors Bulletin No. 630, " Revised Timing Procedures - 10-720 " |
| S.B. 508 | Magneto, Teledyne Continental Motors Bulletin No. 639, " Proper Installation of Impulse Couplings " |
| S.B. 515 | Magneto, Teledyne Continental Motors Bulletin No. 643, " Maintenance Intervals for all TCM and Bendix Aircraft Magnetos and Related Equipment " |
| S.B. 517* | Magneto, Teledyne Continental Motors Critical Bulletin No. CSB641, " Poss. Open Cond. of SC-20, -200,-1200Mag. Capacitor " (A.D. #9406-09) |
| S.I. 1314 | Magnetos (Bendix), Replacement of Slick Ignition Leads Furnished on |
| S.B. 516 | Magnetos, Inspection and Removal of TCM and Bendix S-20and S-1200 Series Impulse Coupling |
| S.I. 1346A | Magnetos, Installation of Bendix S4LN-1208 |
| S.B. 235A | Magnetos, Procedure for Inspection of Type SN-20 & SN-21 (Lightweight) |
| S.I. 1470 | Magnetos, Replacement of Teledyne Continental Motors S-20 and S-200 with SC-20 and SC-200 (Short Cover) |
| S.I. 1133 | Magnetos, S-700 Series, Timing Procedure |
| S.I. 1374B | Magnetos, Slick |
| S.I. 1443B | Magnetos, Slick, Approved on Textron Lycoming Engines |
| S.B. 313B | Maintenance and Inspection of Turbocharger |
| S.I. 1080A | Maintenance Items for Special Attention |
| S.B. 301 B | Maintenance Procedures and Service Limitations for Valves |
| S.I. 1425A | Maintenance Procedures to Reduce Possibility of Valve Sticking |
| S.I. 1040A | Maintenance Procedures, Simmonds 530 Fuel Injection System |
| S.I. 1363 | Manifold Ball Joint and Retaining Strap, Exhaust |
| S.I. 1320 | Manifold Components, Exhaust, Tightening Procedures |
| S.I. 1410 | Manifold Pipe Improvement, Exhaust |
| S.I. 1337A | Manifold Pressure Relief Valve - TIGO-541 |
| S.I. 1293 | Manifold Pressure Relief Valve - TIO-541 |
| S.I. 1257E | Manifold Pressure, Horsepower and RPM Values |
| S.I. 1391 | Manifold Tube Alignment, Exhaust |
| S.I. 1190 | Manifold Tube Modification, Exhaust |
| S.I. 1455 | Manifold, Fuel Injection, Installation of Kit P/N 05K21433 |
| S.B. 512 | Marmon Flange Joint, Inspection at Transition Inlet |
| S.L. L186 | Marvel-Schebler Bulletin No. A1-76, " Carburetor Cleaning " |
| S.I. 1370 | Marvel-Schebler Bulletin No. A1-78, " Carburetor Mixture Control Retainer " |
| S.B. 434* | Marvel-Schebler Bulletin No. A1-79, " Improve Sealing of Economizer Channel, HA-6 Carbs. " (A.D. #79-15-02) |
| S.I. 1373 | Marvel-Schebler Bulletin No. A2-78, " Sealing Pump & Economizer Rods, Carb. " |
| S.B. 436* | Marvel-Schebler Bulletin No. A2-79, " Possible Carburetor Contamination " (A.D. #79-08-06) |
| S.B. 310 | Marvel-Schebler Bulletin No. A3-66, " Replacement of Venturi " |
| S.I. 1398A | Marvel-Schebler Carburetor Modification - 0-540 |
| S.I. 1421 | Marvel-Schebler Carburetor Modification - TO-360 |
| S.B. 352 | Marvel-Schebler/Tillotson Bulletin No. 1-71, " Securing Cam Lever " |
| S.I. 1413 | Marvel-Schebler/Tillotson Bulletin No. A1-81, " Model HA Carburetor Float Shaft and Bracket Wear " |
| S.B. 514 | McCauley Bulletin No. 202A, " Replacement of Governor Flyweight Assy. and Pilot Spool End Fitting " |
| S.L. L230 | Microfiche, Publications Available on (Refer to Supplement Nos. 1 and 2 to S.L. L230) |
| S.L. L132 | Military Aircraft Engines, Service Policy |
| S.I. 1026 | Mixture Control Installation Procedure, Simmonds Model 580 Fuel Injector |
| S.I. 1094D | Mixture Leaning Procedures, Fuel |
| S.B. 484* | Modification, Inspection, Alignment and, of Crossover Exhaust Assembly (A.D. #89-12-04) |
| S.I. 1264 | Moisture Drains, Addition of Magneto Cover |
| S.I. 1157 | Motors, Starter, Periodic Maintenance |
| S.B 420 | Mount Assy., Turbocharger |
| S.I. 1408 | Mount Replacement, Engine |
| S.I. 1170 | Mounting Bolt, Generator Replacement |
| S.I. 1248B | Mounting Bracket Attaching Bolts, Engine |
| S.I. 1380* | Mounting Bracket Attaching Nuts or Bolts, Engine (A.D. #79-10-03) |
| S.I. 1306A | Mounting Bracket Installation, Compressor |
| S.I. 1270A | Mounting Bracket Shims, Alternator |
| S.I. 1105A | Mounting Brackets, Generator/Alternator, Periodic Inspection |
| S.I. 1298 | Mounting Dowel Removal, Engine |
| S.I. 1415 | Mounting Hardware, New Turbocharger |
| S.I. 1364 | Mounting Pad Surface Repair, Oil Pump |
| S.I. 1232 | Mounting Plate Assembly Procedure, Compressor |
| S.B. 344 | Mounting Plate Assembly Procedure, Compressor |
| S.I. 1173 | Mounting Stud, Intake Pipe, Replacement |
| S.I. 1448 | Muffler Covers (Heater), Installation of Tailpipes and (Refer to Supplement Nos. 1 and 2 to S.l. 1448) |
| S.I. 1304G | Nameplate Replacement, Engine |
| S.B. 212B | Necked Studs, Replacing Straight Thru-Studs With |
| S.I. 1047B | Nitride Hardened Steel Cylinders, Inspection and Reconditioning Procedures |
| S.I. 1465 | Non-Counterweighted Engine Models, Crankshaft Assemblies for |
| S.B. 510 | Nozzle Assys., Fuel Injector, Recall, Precision Airmotive Bulletin No. PRS-101 (Refer to Supplement No. 1 to S.B. 510) |
| S.I. 1271A | Nozzle Replacement, Carburetor- 0-235 |
| S.I. 1395A | Nozzle Replacement, Carburetor - 0-320-D2A |
| S.I. 1305C | Nozzle Replacement, Carburetor - 0-320-E2A, -E2D, -E2G, -E3D ,' |
| S.I. 1072 | Nozzles, Fuel Injection, for Simmonds No. 530 Fuel Injection System |
| S.I. 1275B | Nozzles, Fuel Injector, Cleaning |
| S.I. 1231 | Nozzles, Fuel Injector, Torque Requirement |
| S.I. 1106D | Nut, Connecting Rod Bolt, Crimping Requirements |
| S.I. 1210B* | Nut, Pinion Cage Attaching, Replacement (A.D. #69-25-08) |
| S.I. 1380* | Nuts or Bolts, Engine Mounting Bracket Attaching (A.D. #79-10-03) |
| S.B. 213A | Nuts, Cylinder Base Allen Head, Replacing Cylinder Base Spline Nuts with |
| S.I. 1388C* | 0-235 Series Engines, Troubleshooting (A.D. #80-25-02) |
| S.B. 453C* | 0-235 Series, Push Rods (A.D. #80-25-02) |
| S.L. L156 | 0-290-G Surplus Power Plant Engines (FAA Release No. 462) |
| S.L. L225 | 0-320, 0-320-A1A, -A1B, -B1A and -BIB Engines, Parts Information |
| S.I. 1123C | O-Ring Seal, Installation of P/N STD-2013 at Doweled Thru Stud Locations |
| S.L. L226 | Oil Additive, P/N LW-16702, Discoloration |
| S.B. 471 | Oil Additive, Use of Avco Lycoming LW-16702 |
| S.B. 446C* | Oil Additive, Use of Avco Lycoming LW-16702 (A.D. #80-04-03) |
| S.I. 1409A | Oil Additive, Use of Avco Lycoming LW-16702 (Refer to Supplement No. 1 to S.l. 1409A) |
| S.L. L171 | Oil Analysis, General Aspects of Spectrometric |
| S.B. 480 | Oil and Filter Change and Cleaning |
| S.B. 480 | Oil Change, and Filter, and Cleaning |
| S.I. 1124B | Oil Consumption Test Limits |
| S.I. 1462 | Oil Control, Propeller Leak Test Procedure |
| S.I. 1423 | Oil Cooler Bypass Valve P/N 75944, Thermostatic |
| S.I. 1316A | Oil Cooler Bypass Valve Seat, Repair of |
| S.I. 1255 | Oil Cooler Bypass Valve, Thermostatic, Replacement |
| S.I. 1008B | Oil Cooler Bypass, Thermostatic, Instructions for Installation |
| S.I. 1399 | Oil Drain tube Replacement, Turbocharger |
| S.B. 377 | Oil Drain, Modification, and Turbocharger Check Valve |
| S.I. 1169C | Oil Filter Assy., Inspection and Replacement |
| S.B. 370 | Oil Filter Attaching Stud Replacement |
| S.B. 466 | Oil Filter Base Adapter Inspection |
| S.I. 1442 | Oil Filter Bypass Valve, Improved |
| S.I. 1453 | Oil Filter Converter Plate Gasket, Replacement of |
| S.B. 337A | Oil Filter Housing and Bolt Modification |
| S.I. 1457 | Oil Filter Kit, Remote Mount, Textron Lycoming |
| S.B. 397 | Oil Filter Seals, Full Flow - TIO & TIGO-541 Series |
| S.I. 1403 | Oil Filters, Approved Spin-On, Champion Bulletin No. 75-4 |
| S.I. 1109 | Oil Filters, Procedures for Cleaning Simmonds Fuel Injector |
| S.I. 1397 | Oil from Breather Fitting, Overflow, Inverted Oil System |
| S.I. 1274B | Oil Hoses, Silicone Coated, Service Replacement |
| S.B. 389 | Oil Inlet Check Valve Replacement, Turbocharger |
| S.I. 1290D | Oil Leakage Repair, Crankcase Thru-Stud Locations, Assembled and Unassembled Engines |
| S.B. 407A* | Oil Level Gage Assys. (A.D. #77-07-07) |
| S.I. 1379 | Oil Level Gage Kit |
| S.I. 1288 | Oil Level Gage, Modification of |
| S.B. 451 | Oil Level Gage, Rework or Replacement |
| S.I. 1435 | Oil Line, Propeller Governor, Nut and Elbow (Refer to Supplement No. 1 to S.l. 1435) |
| S.B. 247 | Oil Metering Plug Modification in Accessory Housing |
| S.I. 1251 | Oil Plug, Crankshaft Front, PC-111 and PC-112 Listing |
| S.I. 1172C | Oil Pressure Relief Valve Installation, Adj. and Valve Seat Repair or Replacement |
| S.I. 1300 | Oil Pressure, Increased Turbocharger Inlet |
| S.I. 1164A | Oil Pump Application |
| S.I. 1341 | Oil Pump Idler Shaft Lubrication |
| S.B. 385C* | Oil Pump Impeller and Drive Replacement (Refer to Supplement No. 1 to S.B. 385C) (A.D. #75-08-09) |
| S.I. 1230B | Oil Pump Impellers |
| S.I. 1434 | Oil Pump Impellers, Improved |
| S.B. 423* | Oil Pump Inspection and Impeller Replacement (A.D. #78-12-08) |
| S.I. 1364 | Oil Pump Mounting Pad Surface Repair |
| S.B. 381C* | Oil Pump Woodruff Key Drive and Impeller Replacement (A.D. #75-08-09) |
| S.I. 1273A | Oil Pump, Installation of Relief Valve |
| S.I. 1392 | Oil Recommendations, Lubricating, and Cold Weather Operation |
| S.I. 1411 | Oil Seal Application, Thru-Bolt Ring |
| S.I. 1111 | Oil Seal Surface, Crankshaft, Recondition of Worn |
| S.I. 1221A | Oil Seal, Dry Air Pump Drive, Replacement |
| S.I. 1324A | Oil Seals, Crankshaft |
| S.I. 1313A | Oil Squirt Turbocharger Installation |
| S.B. 345 | Oil Suction Tube Assembly Modification |
| S.I. 1289A | Oil Sump and Related Parts Listing - PC-206 |
| S.B. 489A | Oil Sump Baffle Assembly P/N LW-13383 |
| S.I. 1279A | Oil Sump Baffle Replacement |
| S.B. 258 | Oil Sump Induction Modification to Eliminate Engine Roughness in Piper Aircraft |
| S.I. 1168B | Oil Sump, Repair of Intake Pipe Bores |
| S.I. 1369 | Oil Supply Port, Vacuum Pump Pad |
| S.I. 1321 | Oil Transfer and Supply Tubes - Propeller |
| S.I. 1394 | Oil Transfer Dowel, Modification to Retrofit Hollow, on Accessory Housing and Cover Assys. |
| S.B. 318B | Oil, Lubricating, Limitations (Break-In) |
| S.I. 1014K | Oil, Lubricating, Recommendations |
| S.L. L203 | Oil, Lubricating, Recommendations |
| S.B. 399 | Oil, Lubricating, Safe Quantity |
| S.I. 1472 | Oil Preservative, Removal From Engine |
| S.L. L229A | Oil Synthetic Lubricating, Use of Mobil AV 1, in Textron Lycoming Reciprocating Aircraft Engines |
| S.B. 3691 | Overboost, Engine Inspection After |
| S.I. 1397 | Overflow Oil from Breather Fitting of Inverted Oil System |
| S.L. L161C | Overhaul Manual Revision Policy |
| S.L. L209A | Overhaul Manuals and Parts Catalogs, Utilization of Textron Lycoming Piston Engine |
| S.I. 1427B | Overhaul, Engine Test After (With Engine Installed in Aircraft) |
| S.B. 240M | Overhaul, Normal, Parts Replacement |
| S.I. 1009AJ | Overhaul, Recommended Time Between (TBO) - (Reactivated - Supersedes S.L. L201C) |
| S.B. 276 | Overhaul, Replacement of Front Main Bearing |
| S.I. 1123C | Oversized Dowel, Installation of P/N 75302-P10 at Thru-Stud Locations |
| S.B. 3691 | Overspeed, Engine Inspection After |
| S.I. 1364 | Pad Surface Repair, Oil Pump Mounting |
| S.B. 271A | Painting of Cylinder Flange Area |
| S.L. L223 | Part Number Code, New |
| S.I. 1285A | Particle Inspection, Magnetic |
| S.I. 1125B | Parting Surface Sealants, Alternate Crankcase |
| S.L. L227A | Parts Catalogs and Applicable SSP's and/or Revisions |
| S.L. L209A | Parts Catalogs and Overhaul Manuals, Utilization of Textron Lycoming Piston Engine |
| S.L. L225 | Parts Information, 0-320, 0-320-A1A, -A1B, -B1A and -BIB Engines |
| S.I. 1289A | Parts Listing - PC-206, Oil Sump and Related |
| S.B. 240M | Parts Replacement at Normal Overhaul |
| S.I. 1218A | Parts Substitution Chart, Camshaft with Integral Drive Gear |
| S.I. 1059C | Parts, Pre-Lubrication Prior to Assembly |
| S.I. 1122A | Parts, Turbocharger, Repair Procedures for |
| S.I. 1340 | Pin Identification, Piston |
| S.I. 1267B | Pin Plug Usage, Piston |
| S.I. 1376 | Pin Replacement, Starter Drive |
| S.L. L182 | Pin, Piston, Finish |
| S.B. 501 B* | Pin, Piston, P/N LW-14077, Recall of (A.D. #92-12-05) |
| S.I. 1156A | Pinion Cage Assy. and Propeller Shaft Procedure |
| S.I. 1210B* | Pinion Cage Attaching Nut Replacement (A.D. #69-25-08) |
| S.I. 1236A | Pinion Cages, Reduction Gear, Repair Procedure for Worn [Refer to Supplement No. 1 to S.l. 1236A) |
| S.I. 1461 | Pinion, Improved for Lightweight Starter P/N 31B21064 (24V) and P/N 31A21198 (12V) |
| S.I. 1355 | Pipe Extensions and Clamps, Intake |
| S.I. 1410 | Pipe Improvement, Exhaust Manifold |
| S.B. 499B* | Pipe Kit, Exhaust (05K21503), One-Piece, Installation of (A.D. #91-21-01) |
| S.I. 1216 | Pipe, Intake, and Seal Replacement |
| S.I. 1243 | Piston Identification and Inspection |
| S.L. L182 | Piston Pin Finish |
| S.I. 1340 | Piston Pin Identification |
| S.I. 1267B | Piston Pin Plug Usage |
| S.B. 367F* | Piston Pin, P/N 69650, Required Inspection (Refer to Supplement No. 1 to S.B. 367F) (A.D. #73-23-01) |
| S.B. 501B* | Piston Pin, P/N LW-14077, Recall of (A.D. #92-12-05) |
| S.L. L215 | Piston Replacement Recommendation |
| S.I. 1471 | Piston Usage |
| S.B. 520 | Piston, Incorrect Shipped with Cylinder Kits P/N 05K21108, P/N 05K21118 and P/N 05K21104 |
| S.I. 1037K | Pistons, Approved for Use in Textron Lycoming Aircraft Engines |
| S.I. 1076 | Pitch Alignment, Bevel Gear Assy., Backlash and |
| S.I. 1232 | Plate, Compressor Mounting, Assembly Procedure |
| S.I. 1296 | Plate, Drive, and Crankshaft Attaching Parts |
| S.I. 1438 | Plate, Propeller Governor Pad, P/N LW-12347 |
| S.I. 1228A | Plates, Cylinder Hold-Down, Modification of |
| S.I. 1180B | Plug, Crankshaft Front |
| S.I. 1251 | Plug, Crankshaft Front Oil, PC-! 11 & PC-112 Listing |
| S.I. 1267B | Plug, Piston Pin, Usage |
| S.I. 1424 | Plunger Assy./Hydraulic Tappet P/N 78290, Installation Procedure |
| S.B. 238 | Plunger Assys., Magnetized Condition of Hydraulic Tappet |
| S.I. 1011G* | Plunger Assys., Table of Current (A.D. #62-03-02) |
| S.L. L132 | Policy, Service, Regarding Lycoming Military Aircraft Engines |
| S.I. 1428 | Power Setting, Richer, Carburetor Modification for- O/LO-360-A |
| S.I. 1241 B | Pre-Oiling Engines Prior to Initial Start |
| S.B. 495A | Precision Airmotive Corp. Bulletin No. MSA-1, Rev. 1, Carburetor, " Replacement of Composite Floats With Metal Floats " |
| S.B. 498B | Precision Airmotive Corp. Bulletin No. MSA-2, Rev. 2, Carburetor, " One Piece Primary and Main Venturi " |
| S.B. 510 | Precision Airmotive Corp. Bulletin No. PRS-101, " Recall of Fuel Injector Nozzle Assys. " (Refer to Supplement No. 1 to S.B. 510) |
| S.I. 1445 | Precision Airmotive Corp. Bulletin No. PAS-91, Fuel Injector, " Timing of the Power Enrichment Valve Opening " |
| S.B. 485* | Precision Airmotive Corp. Bulletin No. PAS-92, " Fuel Injector Contamination " (A.D. #89-13-02) |
| S.L. L180A | Preservation, Engine, for Active and Stored Aircraft |
| S.I. 1472 | Preservative Oil, Removal From Engine |
| S.I. 1308C | Pressurized Magneto Pressure Test |
| S.L. L189 | Prestolite Bulletin No. ASM-11, " Bench Testing Solid State Regulators " |
| S.I. 1389 | Prestolite Bulletin No. ASM-12, " Addition of Loctite Grade A to Starting Motors " |
| S.I. 1253 | Prestolite Bulletin No. ASM-5, " Field Terminal Stud Insulation Replacement " |
| S.I. 1237A | Prestolite Bulletins Nos. ASM-3 & ASM-4, " Aircraft Charging System Service Precautions " |
| S.I. 1301A | Primer and Fuel Injector Lines, Identification |
| S.L. L163C | Propeller Blade or Loss, Propeller Strike, Recommendations Regarding |
| S.I. 1312 | Propeller Drive Thrust Bearing Replacement (Crankcase P/N LW-13082) |
| S.I. 1098E | Propeller Flange Bushing Location |
| S.I. 1452 | Propeller Flange Bushings, Reindexing (0-360-C1G) |
| S.I. 1344 | Propeller Flange Dowel Hole Repair |
| S.I. 1343A | Propeller Governor Idler Shaft, Set Screw for |
| S.B. 488A* | Propeller Governor Line Support (Refer to Supplement No. 1 to S.B. 488A) (A.D. #90-04-06) |
| S.I. 1435 | Propeller Governor Oil Line Nut and Elbow |
| S.I. 1438 | Propeller Governor Pad Plate P/N LW-12347 |
| S.I. 1462 | Propeller Oil Control Leak Test Procedure |
| S.I. 1321 | Propeller Oil Transfer and Supply Tubes |
| S.I. 1156A | Propeller Shaft and Pinion Cage Assembly Procedure |
| S.I. 1250 | Propeller Shaft Bearing Lubrication |
| S.I. 1108C | Propeller Shaft Bearing Surfaces, Repair |
| S.I. 1227 | Propeller, Hartzell Letter No. 17, " Oil Leakage " |
| S.B. 514 | Propeller, McCauley Bulletin No. 202A, " Replacement of Governor Flyweight Assembly and Pilot Spool End Fitting " |
| S.L. L230 | Publications Available on Microfiche (Refer to Supplement No. 1 and 2 to S.L. L230) |
| S.L. L114AF | Publications, Engine and Accessory Maintenance |
| S.L. L161C | Publications, Overhaul Manual Revision Policy |
| S.L. L195 | Puller, Seal, ST-172, Revision of |
| S.I. 1283A | Pulley and Belt, Alternator Cog, Installation |
| S.I. 1249 | Pulley, Alternator, and Shaft Assy. |
| S.I. 1221A | Pump Drive (Dry Air) Oil Seal Replacement |
| S.I. 1338 | Pump Drive Shaft Modification, Hydraulic |
| S.I. 1341 | Pump Idler Shaft Lubrication, Oil |
| S.I. 1364 | Pump Mounting Pad Surface Repair, Oil |
| S.B. 494* | Pump Vent Fittings, Fuel, Restricted, Installation of (A.D. #91-08-07) |
| S.B. 487* | Pump Vent, Fuel, Restriction (A.D. #89-15-10) |
| S.I. 1212 | Pump, Accelerator, Marvel-Schebler Carburetors with - 0-235-C Series |
| S.B. 374 | Pump, Fuel Inlet, Inspection |
| S.B. 421* | Pump, Fuel Line Between Fuel Injector and Fuel (A.D. #78-23-08) |
| S.L. L218 | Pump, Fuel, Adapters |
| S.I. 1309 | Pump, Lear Siegler Fuel, Modification |
| S.I. 1164A | Pump, Oil, Application |
| S.I. 1230B | Pump, Oil, Impellers |
| S.I. 1434 | Pump, Oil, Impellers, Improved |
| S.B. 454B* | Pump, Oil, Replacement- HI0-360 (A.D. #81-18-04) |
| S.B. 455D* | Pump, Oil, Replacement - O. IO, TO-360 (A.D. #81-18-04) |
| S.B. 456F* | Pump, Sintered Iron Oil, Replacement of (A.D. #81-18-04) |
| S.I. 1152A | Punch Marks on Crankshaft Counterweight Lobes |
| S.I. 1060E | Push Rod Identification |
| S.B. 453C* | Push Rods, 0-235 Series (A.D. #80-25-02) |
| S.B. 408 | Rajay Industries Service Letter No. 21A, " Inspection of Turbine (Exhaust) Housings " |
| S.B. 501B* | Recall of Piston Pin P/N LW-14077 (A.D. #92-12-05) |
| S.I. 1009AJ | Recommended Time Between Overhaul (TBO) (Reactivated - Supersedes S.L. L201C) |
| S.L. L214A | Reconditioned Camshaft Exchange Program (Notice of Discontinuance of Program) |
| S.L. L150T | Reconditioned Simmonds Fuel Injectors |
| S.I. 1047B | Reconditioning Procedures for Nitride Hardened Steel Cylinders |
| S.B. 319B* | Reduction Gear Assembly Inspection (A.D. #69-25-08) |
| S.I. 1159 | Reduction Gear Housing Interference, Crankcase Modification to Prevent |
| S.I. 1236A | Reduction Gear Pinion Cages, Repair Procedure for Worn (Refer to Supplement No. 1 to S.l. 1236A) |
| S.I. 1446* | Regulator Diaphragm, Possible Ruptured, in AN Fuel Pump (A.D. #91-08-07) |
| S.I. 1154E | Regulators, FAA Approved |
| S.L. L189 | Regulators, Prestolite Bulletin No. ASM-11, " Bench Test Solid State Regulators " |
| S.I. 1154E | Relays, FAA Approved |
| S.I. 1172C | Relief Valve Installation, Adjustable Oil Pressure, and Valve Seat Repair or Replacement |
| S.I. 1273A | Relief Valve, Installation in Oil Pump |
| S.I. 1337A | Relief Valve, Manifold Pressure - TIGO-541 |
| S.I. 1293 | Relief Valve, Manifold Pressure - TIO-541 |
| S.I. 1457 | Remote Mount Oil Filter Kit, Textron Lycoming |
| S.B. 222C | Renitriding Recommendations, Crankshaft |
| S.L. L221 | Repair, Warranty, of Bendix Fuel Metering Components |
| S.L. L222 | Repair, Warranty, of Teledyne Continental Motors Ignition Components |
| S.B. 311 | Retainers (Cushion), Inspection and Replacement |
| S.I. 1277A | Retaining Components, Shroud Tube |
| S.I. 1284A | Retaining Spring Replacement, Shroud Tube |
| S.I. 1363 | Retaining Strap and Ball Joint, Exhaust Manifold |
| S.L. L227A | Revisions and/or SSP's Applicable to Parts Catalogs |
| S.B. 477A* | Rework and Inspection of P/N LW-18790 Rocker Arm Assembly (Refer to Supplement No. 1 to S.B. 477A) (A.D. #87-10-06) |
| S.I. 1428 | Richer Power Setting, Carburetor Modifications for - O/LO-360-A |
| S.L. L233 | Ring Gear, Support Assys., Better Identification of Reverse Rotation |
| S.I. 1121 | Ring Gears, Identification |
| S.I. 1141 | Ring Gears, Starter, Replacement of Worn |
| S.I. 1411 | Ring, Thru-Bolt, Oil Seal Application |
| S.I. 1037K | Rings, Approved for Use in Textron Lycoming Aircraft Engines |
| S.B. 477A* | Rocker Arm Assembly, Inspection and Rework of P/N LW-18790 (Refer to Supplement No. 1 to S.B. (A.D. #87-10-06) |
| S.I. 1454 | Rocker Arm Installation, Parallel Valve |
| S.B. 412B* | Rocker Arm Retaining Stud, Intake and Exhaust Valve (A.D. #77-20-07) |
| S.I. 1268B | Rocker Assy., Exhaust Valve |
| S.I. 1468 | Rocker Assy., Exhaust Valve |
| S.I. 1366A | Rocker Shaft Bearing Hole, Repair Procedure for Worn |
| S.I. 1176 | Rocker Shaft Repair, Valve |
| S.B. 225B | Rocker Thrust Washers, Valve, Replacement of |
| S.I. 1182A | Rockers, High Lift Valve, for Improved Performance |
| S.I. 1307B | Rod Bolt Assembly, Connecting, and Torque Application |
| S.I. 1450 | Rod Bolt, Connecting, and Torque Application, Alternate |
| S.I. 1458 | Rod Bolts, Connecting, Soft |
| S.I. 1318 | Rod Bolts, Connecting, Strengthened |
| S.I. 1311A | Rod Bolts, Oversize Connecting |
| S.I. 1359 | Rod Cap Modification, Connecting |
| S.B. 418 | Rod End Replacement, Waste Gate Control Cable |
| S.I. 1060E | Rod Identification, Push |
| S.I. 1466 | Rod, Connecting, Assemblies |
| S.I. 1467 | Rod, Connecting, Assemblies |
| S.I. 1323A | Rod Connecting, with High-Tensile Strength Bolts |
| S.I. 1469 | Rod Connecting, with High-Tensile Strength Bolts |
| S.B. 439A | Rods, Connecting, Inspection for Fretting and/or Galling, Repair of Fretting |
| S.I. 1138B | Rods, Connecting, Replacement of 10-720 Engines |
| S.B. 351 B* | Rods Heavy Connecting for High Speed Geared Drive Engines (A.D. #74-13-05) |
| S.I. 1075A | Rods Push, Procedure for Removing from Top Exhaust Cylinders |
| S.I. 1012F | Rollers, Location and Proper Assembly Procedure |
| S.B. 406 | Romec Fuel Pump Inspection |
| S.I. 1302A | Rotator Intake Valve with Small Diameter Head |
| S.I. 1280C | Rotator Type Intake Valves |
| S.I. 1449 | Rotomaster Turbocharger (46A21184), Installation of |
| S.I. 1257E | RPM Values, Horsepower and Manifold Pressure |
| S.I. 1140 | Salvage Repair of Magneto Bearing Recess in Crankcase |
| S.I. 1120 | Scintilla Bulletin No. 502, S-700 Series Magnetos " Internal Timing " |
| S.I. 1126 | Scintilla Bulletin No. 503, " Lubrication of Tapered Drive Shaft on S Series Mags. " |
| S.I. 1139 | Scintilla Bulletin No. 510 & 511, " Distributor Gears S-600 Series; Replaceable Electrodes S-700 Series " |
| S.I. 1186 | Screen, Filter, Removal from Fuel Injector Nozzle |
| S.B. 366 | Screw Carburetor Throttle Body, Inspection |
| S.B. 330B* | Screw Retighten and Lockwire Carburetor Throttle Arm (A.D. #72-06-05) |
| S.L. L196 | Screwdriver Blade, ST-418-3, Revision to |
| S.I. 1216 | Seal and Intake Pipe Replacement |
| S.L. L195 | Seal Puller, ST-172, Revision of |
| S.I. 1111 | Seal Surface, Crankshaft Oil, Recondition of Worn |
| S.I. 1347 | Seal Surface, Shroud Tube, Repair of |
| S.I. 1368 | Seal Washer and Retainer, Tachometer Adapter |
| S.B. 354 | Seal, Leakage at Propeller Shaft |
| S.B. 375A | Seal, Moisture, Cross Shaft Support Tube |
| S.I. 1459 | Sealant, Application to Bolt Threads |
| S.I. 1125B | Sealants, Alternate Crankcase Parting Surface |
| S.I. 1324A | Seals, Crankshaft Oil |
| S.B. 397 | Seals, Full Flow Oil Filter |
| S.I. 1329A | Seals, Supercharger Inlet Adapter |
| S.I. 1092A | Seat Replacement, Valve, Tools and Procedures |
| S.I. 1316A | Seat, Oil Cooler Bypass Valve, Repair of |
| S.I. 1262A | Seats, Venturi, and Small Head Intake Valves |
| S.B. 301 B | Service Limitations and Maintenance Procedures for Valves |
| S.L. L132 | Service Policy Regarding Lycoming Military Aircraft Engines |
| S.I. 1345 | Service Replacement Crankcases for Narrow Cylinder Flange Four Cylinder Engines |
| S.I. 1256E | Service Use, Alternate Valve Guides for |
| S.I. 1079B | Servo Fuel Line Filters, Periodic Maintenance |
| S.I. 1343A | Set Screw for Propeller Governor Idler Shaft |
| S.I. 1249 | Shaft Assy. and Alternator Pulley |
| S.I. 1108C | Shaft Bearing Surfaces, Propeller, Repair |
| S.I. 1250 | Shaft Bearing, Propeller, Lubrication |
| S.I. 1208 | Shaft Bore Bushings, Magneto, Installation of |
| S.I. 1366A | Shaft Bushing Hole, Rocker, Repair Procedure for Worn |
| S.I. 1341 | Shaft Lubrication, Oil Pump Idler |
| S.I. 1338 | Shaft Modification, Hydraulic Pump Drive |
| S.I. 1197A | Shaft Recesses, Idler Gear, Repair |
| S.I. 1161 | Shaft, Carburetor Throttle, Modification to Prevent Leakage |
| S.B. 375A | Shaft, Cross, Support Tube Moisture Seal |
| S.I. 1351 | Shaft, Drive, and Drive Gear, Accessory |
| S.I. 1084A | Shaft, Intermediate Supercharger Drive, and Components |
| S.B. 354 | Shaft, Leakage at Propeller Seal |
| S.I. 1343A | Shaft, Propeller Governor Idler, Set Screw for |
| S.I. 1156A | Shaft, Propeller, and Pinion Cage Assembly Procedure |
| S.I. 1176 | Shaft, Repair, Valve Rocker |
| S.I. 1265A | Shaft, Serrated Throttle, and Lever |
| S.I. 1310A | Shafts, Idler, Lockwire for |
| S.I. 1270A | Shims, Alternator Mounting Bracket |
| S.I. 1277A | Shroud Tube Retaining Components |
| S.I. 1284A | Shroud Tube Retaining Spring Replacement |
| S.B. 519 | Shroud Tube Retaining Springs, Removal of LW-14995 Before Further Flight |
| S.I. 1347 | Shroud Tube Seal Surface, Repair of |
| S.I. 1297 | Shroud Tubes w/Helical Spring Retention, Cylinder Modification |
| S.I. 1215 | Shroud Tubes, Correct Installation for Up-Exhaust Engines |
| S.I. 1072 | Simmonds Fuel Injection System No. 530, Fuel Injection Nozzles |
| S.I. 1040A | Simmonds Fuel Injection System No. 530, Maintenance Procedures |
| S.I. 1062 | Simmonds Fuel Injection System No. 570, Maintenance Procedures - Fuel Vent Return "Tee" Fitting |
| S.I. 1069A | Simmonds Fuel Injection System No. 580, Procedure for Inspection & Adjustment to Regulate Fuel Flow |
| S.I. 1026 | Simmonds Model No. 580 Fuel Injector Mixture Control Installation Procedure |
| S.I. 1407 | Simmonds Precision Bulletin No. V-1164, " Periodic Inspection & Overhaul of Injection Pumps " |
| S.B. 456F* | Sintered Iron Oil Pump Impellers, Replacement of (A.D. #81-18-04) |
| S.B. 331 | Sleeve, Inspection & Removal in Fuel Injector Lines (Rubber) |
| S.B. 178A | Sleeve, Reduction Gear Housing, Repair of Worn |
| S.B. 432* | Slick Electro Bulletin No. 1-78, " Magneto/Condenser Replacement " (A.D. #78-25-01) |
| S.I. 1385 | Slick Electro Bulletin No. 1-79, " Grounding for Non-impulse Magnetos " (From 4000, 4100 to 4200 Series) |
| S.B. 449* | Slick Electro Bulletin NO 1-80, " Impulse Coupling Hubs " (A.D. #80-06-05) |
| S.B. 457A | Slick Electro Bulletin No. 1-81, " Magneto Malfunction Due to Cracking of Coil Potting Compound " |
| S.B. 478A | Slick Electro Bulletin No. 1-86, " Impulse Coupling Inspection " |
| S.L. L173B | Slick Electro Bulletin No. 2-80, " Recommended Maintenance & Inspection " |
| S.B. 468B | Slick Electro Bulletin No. 7-83A, " Magneto Bearing Inspection " |
| S.L. L210 | Slick Electro Bulletin No. SB1-85, " Impulse Coupling Hub Assembly Replacement Program " |
| S.I. 1357A | Slick Electro Instructions No. 1-77, " Lag Angle Inspection " and No. 2-77, " Improved Performance " |
| S.L. L177A | Slick Electro Magneto Replacement Policy |
| S.I. 1189 | Slick Impulse Coupling Magneto, Malfunction |
| S.I. 1374B | Slick Magnetos |
| S.I. 1443B | Slick Magnetos, Approved on Textron Lycoming Engines |
| S.B. 393C | Slip Joint Modification, Exhaust |
| S.B. 479 | Slip Joint Modification, Exhaust, and Inspection of P/N 77429 Right Intermediate Exhaust Pipe |
| S.I. 1167 | Sludge Tube Assembly and Test |
| S.I. 1113A | Sludge Tubes, Crankshaft Assy.Revised to Eliminate |
| S.B. 405 | Spacer, Turbo Strut |
| S.B. 359 | Spark Plug Change |
| S.L. L192B | Spark Plug Fouling |
| S.I. 1043A | Spark Plug, Heli-Coil Insert Replacement |
| S.I. 1042T | Spark Plugs, Approved (Refer to Supplement No. 1 to S.l. 1042T) |
| S.L. L227A | Special Service Publications (SSP's) and/or Revisions Applicable to Parts Catalogs |
| S.I. 1070K | Specified Fuels |
| S.L. L171 | Spectrometric Oil Analysis, General Aspects of |
| S.I. 1145 | Spline Drive, Modification to Incorporate Large into Accessory Drive Shaft |
| S.B. 507 | Spotfaces, Missing on P/N 74218 Cylinder Head Assembly |
| S.I. 1192 | Spring Compressor No. ST-266, Valve |
| S.I. 1284A | Spring Replacment, Shroud Tube Retaining |
| S.I. 1381 | Spring Seat Upper Exhaust Valve, and Hydraulic Lifter, Replacement |
| S.B. 447A* | Spring Seat Upper Exhaust Valve, Inspection (AD. #80-1407) |
| S.B. 435* | Spring Seat, Upper Exhaust, Replacement of Hydraulic Lifter and (Refer to Supplement No. 1 and 2 to S.B. 435) (A D. #80-04-03) |
| S.I. 1240C | Spring, Valve, Replacement |
| S.L. L220 | Standard Cylinder Flange Engines, Non-Availability of New |
| S.I. 1383 | Starter Conversion |
| S.I. 1239 | Starter Drive Assembly Replacement |
| S.I. 1118A | Starter Drive Gear Replacement |
| S.I. 1242A | Starter Drive Gear, Thrust Washers for |
| S.I. 1278 | Starter Drive Lubrication |
| S.I. 1287 | Starter Drive Modification: Cold Weather Starting |
| S.I. 1376 | Starter Drive Pin Replacement |
| S.I. 1224 | Starter Modification, VO-435-B1A |
| S.I. 1157 | Starter Motors, Periodic Maintenance |
| S.B. 486 | Starter Ring Gear Support Assemblies, Inspection of Single Belt Driven |
| S.I. 1141 | Starter Ring Gears, Replacement of Worn |
| S I 1451A | Starter, Alternator and Compressor Installation |
| S.I 1461 | Starter, Lightweight, Improved Pinion for P/N 31B21064 (24V) and P/N 31A21198 (12V) |
| S.I. 1447B | Starter, Lightweight, Installation Instructions |
| S.I. 1154E | Starters, FAA Approved |
| S.I. 1121 | Starters, Identification |
| S.I. 1025 | Starters, Recommended Torque Setting |
| S.I. 1389 | Starting Motors, Prestolite Bulletin No. ASM-12, " Addition of Loctite Grade A " |
| S.I. 1362 | Starting, Hard |
| S.I. 1425A | Sucking Valve, Maintenance Procedure to Reduce Possibility of |
| S.I. 1266 | Strap, Alternator Ground - All Engines with Prestolite |
| S.I. 1315A | Strut Bracket and Clamp installation, Turbocharger |
| S.I. 1173 | Stud, Intake Pipe Mounting, Replacement |
| S.B. 370 | Stud Oil Filter Attaching, Replacement |
| S.B. 412B* | Stud Retaining, Intake and Exhaust Valve Rocker Arm (A.D. #77-20-07) |
| S.I. 1196 | Studs, Reduction Gear Attaching, Replacement |
| S.I. 1279A | Sump Bame Replacement, Oil |
| S.I. 1289A | Sump, Oil and Related Parts Listing - PC-206 |
| S.B. 489A | Sump, Oil, Baffle Assembly P/N LW-13383 |
| S.I. 1168B | Sump, Oil, Repair of Intake Pipe Bores |
| S.I. 1295 | Supercharger Adapter Bearing, Oversize |
| S.I. 1084A | Supercharger Drive Shaft, Intermediate, and Components |
| S.I. 1032G | Supercharger Impeller Assys., Parts Replacement and Dynamic Balance |
| S.I. 1329A | Supercharger Inlet Adapter Seals |
| S.B. 367F-1* | Supplement No. 1 to Service Bulletin No. 367F (A.D. #73-23-01) |
| S.B. 373-1 | Supplement No. 1 to Service Bulletin No. 373 |
| S.B. 385C-1* | Supplement No. 1 to Service Bulletin No. 385C (A.D. #75-08-09) |
| S.B. 391A-1 | Supplement No. 1 to Service Bulletin No. 391A |
| S.B. 392B-1 | Supplement No. 1 to Service Bulletin No. 392B |
| S.B. 428-1* | Supplement No. 1 to Service Bulletin No. 428 (A.D. #78-23-10) |
| S.B. 430-1* | Supplement No. 1 to Service Bulletin No. 430 (A.D. #78-23-10) |
| S.B. 435-1* | Supplement No. 1 to Service Bulletin No. 435 (A.D. #80-04-03) |
| S.B. 442-1* | Supplement No. 1 to Service Bulletin No. 442 (A.D. #'s 79-21-08 & 79-26-03) |
| S.B. 467-1* | Supplement No. 1 to Service Bulletin No. 467 (A.D. #83-22-04) |
| S.B. 477A-1 | Supplement No. 1 to Service Bulletin No. 477A |
| S.B. 488A-1* | Supplement No. 1 to Service Bulletin No. 488A (A.D. #90-04-06) |
| S.B. 510-1 | Supplement No. 1 to Service Bulletin No. 510 |
| S.I. 1012F-1 | Supplement No. 1 to Service Instruction No. 1012F |
| S.I. 1029D-1 | Supplement No. 1 to Service Instruction No. 1029D |
| S.I. 1042T-1 | Supplement No. 1 to Service Instruction No. 1042T |
| S.I. 1112E-1 | Supplement No. 1 to Service Instruction No. 1112E |
| S.I. 1143B-1 | Supplement No. 1 to Service Instruction No. 1143B |
| S.I. 1236A-1 | Supplement No. 1 to Service Instruction No. 1236A |
| S.I. 1316A-1 | Supplement No. 1 to Service Instruction No. 1316A |
| S.I. 1377-1 | Supplement No. 1 to Service Instruction No. 1377 |
| S.I. 1409A-1 | Supplement No. 1 to Service Instruction No. 1409A |
| S.I. 1431-1 | Supplement No. 1 to Service Instruction No. 1431 |
| S.I. 1435-1 | Supplement No. 1 to Service Instruction No. 1435 |
| S.I. 1439-1 | Supplement No. 1 to Service Instruction No. 1439 |
| S.I. 1448-1 | Supplement No. 1 to Service Instruction No. 1448 |
| S.I. 1187G-1 | Supplement No. 1 to Service Instruction No. 1187G |
| S.L. L230-1 | Supplement No. 1 to Service Letter No. L230 |
| S.B. 392B-2 | Supplement No. 2 to Service Bulletin No. 392B |
| S.B. 435-2* | Supplement No. 2 to Service Bulletin NO. 435 (A.D. #80-04-03) |
| S.B. 467-2* | Supplement No. 2 to Service Bulletin No. 467 (A.D. #83-22-04) |
| S.I. 1029D-2 | Supplement No. 2 to Service Instruction No. 1029D |
| S.I. 1143B-2 | Supplement No. 2 to Service Instruction No. 1143B |
| S.I. 1448-2 | Supplement No. 2 to Service Instruction No. 1448 |
| S.L. L230-2 | Supplement No. 2 to Service Letter No. L230 |
| S.I. 1369 | Supply Port, Vacuum Pump Pad Oil |
| S.L. L233 | Support Assy., Better Identification of Reverse Rotation Ring Gear |
| S.I. 1384 | Support Assy., Turbocharger, w/Large Spools & Support Installation Instructions |
| S.B. 342B* | Support Clamp and Fuel Line Inspection and Installation (A D. #92-12-10) |
| S.I. 1149 | Support Web, Crankcase Bearing, Inspection & Modification |
| S.L. L229A | Synthetic Lubricating Oil, Use of Mobil AV 1, in Textron Lycoming Reciprocating Aircraft Engines |
| S.I. 1361 | T-Bolt Hose Clamps |
| S.I. 1368 | Tachometer Adapter Seal Washer and Retainer |
| S.B. 492A | Tailpipe Installation, Redesigned V-Band Couplings for |
| S.I. 1448 | Tailpipes, Installation of Heater Muffler Covers and (Refer to Supplement No. 1 and 2 to S.l. 1448) |
| S.I. 1011G* | Tappet Bodies Hydraulic, Table of Current (A D. #62-03-02) |
| S.L. L206A | Tappet Bodies (Cam Followers), Field-Reconditioned |
| S.I. 1336 | Tappet Body Identification |
| S.I. 1334A | Tappet Bore Repair, Crankcase |
| S.I. 1068A* | Tappet Clearance (A D. #80-25-02) |
| S.B. 424* | Tappet Replacement, Hydraulic (A D. #77-20-07) |
| S.I. 1424 | Tappet, Hydraulic/Plunger Assy. P/N 78290, Installation Procedure |
| S.B. 402 | Tappet, Valve Clearance |
| S.I. 1009AJ | TBO, Recommended Rime Between Overhaul (Reactivated - Supersedes S.L. L201C) |
| S.B. 516 | TCM and Bendix S-20 and S-1200 Series Impulse Coupling Magnetos, Inspection and Removal |
| S.L. L190 | TOP, Use of Fuel Additive |
| S.I. 1444 | Teledyne Continental Motors Bulletin No. 630, " Revised Timing Procedures " |
| S.B. 508 | Teledyne Continental Motors Bulletin No. 639, " Proper Installation of Impulse Couplings " |
| S.B. 515 | Teledyne Continental Motors Bulletin No. 643, " Maintenance Intervals for all TCM and Bendix Aircraft Magnetos and Related Equipment." |
| S.B. 517* | Teledyne Continental Motors Critical Bulletin No. CSB641, " poSS. Open Condition of SC-20,-200, -1200 Series Mag. Capacitor " (A.D. #94-06-04) |
| S.L. L222 | Teledyne Continental Motors Ignition Components, Warranty Repair |
| S.I. 1470 | Teledyne Continental Motors Replacement of S20 and S200 Series Magnetos with SC20 and SC200 (Short Cover) Series Magnetos |
| S.I. 1144 | Test Stand (64765), Vertical, Use & Maintenance of 4-Lug Test Drive Assy. (64894) w/ |
| S.B. 113 | Test Stand Installation, Dry Sump, for Lycoming Opposed Series Engines |
| S.I. 1423 | Thermostatic Oil Cooler Bypass Valve P/N 75944 |
| S.I. 125E | Thermostatic Oil Cooler Bypass Valve Replacement |
| S.B. 330B* | Throttle Arm Screw, Carburetor, Retighten and Lockwire (A.D. #72-06-05) |
| S.B. 366 | Throttle Body Screw, Carburetor, Inspection |
| S.I. 1265A | Throttle Lever and Shaft, Serrated |
| S.I. 1161 | Throttle Shaft, Carburetor, Modification to Prevent Leakage |
| S.I. 1411 | Thru-Bolt Ring - Oil Seal Application |
| S.I. 1123C | Thru-Stud Locations, Installation of P/N 75302 Dowel, P/N 75302-P10 Oversized Dowel and P/N STD-2013 O-Ring Seal |
| S.I. 1326 | Thru-Stud Spotface, Crankcase Repair |
| S.I. 1290D | Thru-Stud, Crankcase, Repair of Oil Leakage, Assembled and Unassembled Engines |
| S.B. 212B | Thru-Studs (Straight), Replacing with Necked Studs |
| S.I. 1029D | Thru-Studs, Crankcase, Tightening Procedures for Bolts and (Refer to Supplement No. 1 and 2 to S.I. 1029D) |
| S.B. 273A | Thru-Studs, Modification to Incorporate Body Fit to Crankcase Center Main Bearing Support |
| S.B. 272A | Thru-Studs, Retorqueing of Center Main (Lycoming P/N 68751) |
| S.I. 1312 | Thrust Bearing Replacement, Propeller Drive (Crankcase P/N LW-13082) |
| S.I. 1356 | Thrust Bearing, Oversize, for Reduction Gear |
| S.B. 390A | Thrust Bearing, Propeller (LW-12978), Inspection |
| S.I. 1292A | Thrust Bearing, Stainless Steel, and Lubrication Modifications |
| S.B. 400 | Thrust Buttons, Teflon, Installation of |
| S.I. 1354B | Thrust Face Repair, Crankcase |
| S.I. 1242A | Thrust Washers for Starter Drive Gear |
| S.B. 225B | Thrust Washers, Valve Rocker, Replacement of |
| S.I. 1029D | Tightening Procedures for Crankcase Thru-Studs and Bolts (Refer to Supplement No. 1 and 2 to S.I. 1029D) |
| S.L. L213A | Time Between Overhaul (TBO) Extension Kit |
| S.I. 1325A | Timing Change for IO-360 Series Engines |
| S.I. 1437 | Timing Marks, Engine |
| S.I. 1133 | Timing Procedure for S-700 Series Magnetos |
| S.B. 406 | Titan Fuel Pump Inspection |
| S.L. L232 | Tool Loaning, Discontinuance |
| S.L. L234 | Tool Rental Program |
| S.L. L217 | Tooling Update Kits, Counterweight |
| S.I. 1143B | Tooling Update, Counterweight Bushing and Replacement (Refer to Supplement No. 1 to S.I. 1143B) |
| S.I. 1450 | Torque Application, Alternate Connecting Rod Bolt and |
| S.I. 1238A | Torque Procedures and Assembly, V-Band Couplings |
| S.I. 1231 | Torque Requirements for Fuel Injector Nozzles |
| S.I. 1025 | Torque Setting, Recommended for Starters |
| S.I. 1213 | Torque Value, Increased for Connecting Rod Bolts |
| S.B. 473 | Transition Assembly, P/N LW-16863 |
| S.B. 491A* | Transition Bolts, Inspection of Exhaust (A.D. #91-10-04) |
| S.B. 395 | Transition Coupling Replacement |
| S.B. 512 | Transition Inlet, Inspection of Marmon Flange Joint |
| S.B. 448* | Transition Waste Gate Assy., Turbocharger (A.D. #80-17-10) |
| S.I. 1388C* | Troubleshooting of the 0-235 Series Engines (A.D. #80-25-02) |
| S.I. 1391 | Tube Alignment, Exhaust Manifold |
| S.B. 345 | Tube Assy., Modification, Oil Suction |
| S.I. 1167 | Tube Assy., Sludge and Test |
| S.I. 1190 | Tube Modification, Exhaust Manifold |
| S.I. 1390 | Tube Replacement, Carburetor Idle |
| S.I. 1399 | Tube Replacement, Turbocharger Oil Drain |
| S.I. 1277A | Tube Retaining Components, Shroud |
| S.I. 1284A | Tube Retaining Spring Replacement |
| S.I. 1347 | Tube Seal Surface, Shroud, Repair of |
| S.B. 519 | Tube, Shroud, Retaining Springs Removal of LW-14995 Before Further Flight |
| S.B. 375A | Tube, Support, Cross Shaft Moisture Seal |
| S.I. 1321 | Tubes, Oil Transfer and Supply, Propeller |
| S.I. 1215 | Tubes, Shroud Correct Installation for Up-Exhaust Engines |
| S.I. 1075A | Tubes, Shroud Procedure for Removing from Top Exhaust Cylinders |
| S.I. 1113A | Tubes, Sludge, Crankshaft Assy. Revised to Eliminate |
| S.B. 347 | Turbine Housing Inspection & Replacement, AiResearch Bulletin No. 571-1 |
| S.B. 329A | Turbine Housing Inspection, AiResearch Bulletin No. TP60-0100 |
| S.B. 452A | Turbo Inspection, AiResearch Bulletin No. TP60-0121 |
| S.B. 405 | Turbo Strut Spacer |
| S.I. 1339A | Turbocharger Bracket - TIO & TIGO-541-E |
| S.B. 377 | Turbocharger Check Valve and Oil Drain Modification |
| S.L. L184A | Turbocharger Control Tester Set |
| S.I. 1187G | Turbocharger Density Controller Adjustment |
| S.I. 1300 | Turbocharger Inlet Oil Pressure, Increased |
| S.B. 383 | Turbocharger Inspection, AiResearch Bulletin No. TP60-0101, " Insp. of Model T1823 Turbochargers w/ Stainless Steel Turbine Housings " |
| S.I. 1313A | Turbocharger Installation, Oil Squirt |
| S.I. 1431 | Turbocharger Linkage and Fuel Metering Adjustments (Refer to Supplement No. 1 to S.l. 1431) |
| S.B. 361 | Turbocharger Modification, AiResearch Bulletin No. 1172-1A |
| S.B. 420 | Turbocharger Mount Assy. |
| S.B. 463 | Turbocharger Mounting Bracket Inspection |
| S.1. 1415 | Turbocharger Mounting Hardware, New ,, |
| S.B. 426* | Turbocharger Oil Drain Flange Replacement (A.D. #80-02-13) |
| S.I. 1399 | Turbocharger Oil Drain Tube Replacement |
| S.B. 389 | Turbocharger Oil Inlet Check Valve Replacement |
| S.I. 1122A | Turbocharger Parts, Repair Procedures for |
| S.I. 1328 | Turbocharger Replacement, AiResearch Letter No. TP61-0002 |
| S.I. 1315A | Turbocharger Strut Bracket and Clamp Installation |
| S.I. 1384 | Turbocharger Support Assy. w/Large Spools & Support Installation Instructions |
| S.B. 448* | Turbocharger Transition Waste Gate Assy. (A.D. #80-17-10) |
| S.I. 1449 | Turbocharger, (46A21184), Rotomaster, Installation of |
| S.B. 379 | Turbocharger, AiResearch Bulletin No. TP60-0103, " Inspection of Remanufactured Waste Gate Valve Assys. " |
| S.I. 1223 | Turbocharger, AiResearch Instruction No. 969-1, " Freeing Turbine Shaft " |
| S.I. 1416 | Turbocharger, AiResearch Letter No. TP61-0039, " Bypass Valve Modification " |
| S.B. 313B | Turbocharger, Maintenance and Inspection |
| S.B. 408 | Turbocharger, Rajay Industries Service Letter No. 21A, " Inspection of Turbine (Exhaust) Housings " |
| S.I. 1286B | Turbochargers (TE0659) w/ Stainless Steel Housings |
| S.B. 391A | Turbochargers, AiResearch Bulletin No. TP6~0105, " Turbocharger Repl. or Mod. " (Refer to Supplement No. 1 to S.B. 391A) |
| S.I. 1215 | Up-Exhaust Engines, Correct Installation of Shroud Tubes |
| S.B. 398 | Use of Incorrect Fuel, Recommendations Regarding |
| S.L. L209A | Utilization of Textron Lycoming Piston Engine Overhaul Manuals and Parts Catalogs |
| S.I. 1238A | V-Band Couplings, Assembly and Torque Procedures |
| S.B. 492A | V-Band Couplings, Redesigned, for Tailpipe Installation |
| S.I. 1369 | Vacuum Pump Pad Oil Supply Port |
| S.I. 1193A | Valve Failure, Inspection in Event of |
| S.B. 503 | Valve Guide Replacement, Exhaust, on TIO-540-AF1A Engines |
| S.I. 1256E | Valve Guides, for Service Use |
| S.B. 490A | Valve Guides, Intake and Exhaust, Installation of |
| S.B. 314C* | Valve Lifting, Replacement of Limited Travel (A.D. #68-08-08) |
| S.I. 1423 | Valve P/N 75944, Thermostatic Oil Cooler Bypass |
| S.B. 419 | Valve Replacement, Exhaust- TO-360 |
| S.L. L181 | Valve Replacement, Intake (Service Instructions, 1262A, & 1302A) |
| S.I. 1255 | Valve Replacement, Thermostatic Oil Cooler Bypass |
| S.B. 348A | Valve Rocker Assy., Clearance Between Cylinder Head and |
| S.I. 1176 | Valve Rocker Shaft Repair |
| S.B. 225B | Valve Rocker Thrust Washers, Replacement of |
| S.I. 1182A | Valve Rockers, High Lift, for Improved Performance |
| S.I. 1172C | Valve Seat Repair or Replacement and Adjustable Oil Pressure Relief Valve Installation |
| S.I. 1092A | Valve Seat Replacement Tools and Procedures |
| S.I. 1316A | Valve Seat, Oil Cooler Bypass, Repair of |
| S.I. 1192 | Valve Spring Compressor No. ST-266 |
| S.I. 1240C | Valve Spring Replacement |
| S.I. 1381 | Valve Spring Seat, Upper Exhaust & Hydraulic Lifter, Replacement |
| S.I. 1425A | Valve Sticking, Maintenance Procedures to Reduce Possibility of |
| S.L. L197A | Valve Sticking, Recommendations to Avoid |
| S.B. 402 | Valve Tappet Clearance |
| S.B. 450 | Valve, AiResearch Bulletin No. TP6t) 0119, " Bypass Valve Modification " |
| S.B. 362A | Valve Check, Fuel Vent Line Installation |
| S.I. 1214A | Valve Exhaust Bypass: Reset for Critical Altitude |
| S.B. 388B | Valve, Exhaust, and Guide, Procedure to Determine Condition |
| S.I. 1116C | Valve, Exhaust, Guide Clearance Modification |
| S.I. 1200A | Valve, Exhaust, Guide, Honing During Replacement |
| S.B. 404 | Valve, Exhaust, Inspection (High Lead Fuel Operation) |
| S.I. 1430 | Valve, Exhaust, Replacement |
| S.I. 1268B | Valve, Exhaust, Rocker Assembly |
| S.I. 1468 | Valve, Exhaust, Rocker Assembly |
| S.B. 384 | Valve, Fuel Drain Check, Modification |
| S.I. 1442 | Valve, Improved Oil Filter Bypass |
| S.B. 412B* | Valve, Intake and Exhaust, Rocker Arm Retaining Stud (A.D. #77-20-07) |
| S.I. 1337A | Valve, Manifold Pressure Relief- TIGO-541 |
| S.I. 1293 | Valve, Manifold Pressure Relief- TIO-541 |
| S.I. 1454 | Valve, Parallel, Rocker Arm Installation |
| S.I. 1008B | Valve, Pressure Relief, Instructions for Installation |
| S.I. 1273A | Valve, Relief, Installation in Oil Pump |
| S.I. 1302A | Valve, Rotator Type, w/Small Diameter Head |
| S.B. 377 | Valve, Turbocharger Check, and Oil Drain Modification |
| S.B. 389 | Valve, Turbocharger Oil Inlet Check, Replacement |
| S.B. 447A* | Valve, Upper Exhaust Spring Seats, Inspection (A D. #80-14-07) |
| S.I. 1136A | Valves, Exhaust w/ 1/2. Diameter Stems, in Parallel Valve Cylinders |
| S.B. 502 | Valves, Intake P/N LW-13262, Replacement, Etched With Date Code K-L |
| S.I. 1280C | Valves, Intake, Rotator Type |
| S.B. 301B | Valves, Maintenance Procedures and Service Limitations |
| S.I. 1262A | Valves, Small Head Intake, and Venturi Seats |
| S.B. 494* | Vent Fittings, Fuel Pump, Restricted, Installation of (A.D. #91-08-07) |
| S.B. 497* | Vent Fittings, Fuel Pump, Restricted, New, Installation in AN Drive (A.D. #91-08-07) |
| S.B. 487* | Vent, Fuel Pump, Restriction (AD. #89-15-10) |
| S.I. 1262A | Venturi Seats and Small Head Intake Valves |
| S.B. 297A* | Venturi, One Piece and Main for Marvel-Schebler MA-45 Carburetors (A.D. #63-22-03) |
| S.I. 1224 | VO-435-B1A, Starter and Magneto Modification |
| S.L. L221 | Warranty Repair of Bendix Fuel Metering Components |
| S.L. L222 | Warranty Repair of Teledyne Continental Motors Ignition Components |
| S.B. 448* | Waste Gate Assy., Turbocharger Transition (A. D. #80- 17- 10) |
| S.B. 418 | Waste Gate Control Cable Rod End Replacement |
| S.B. 472 | Wide Cylinder Flange Crankcases, Disassembly |
| S.I. 1419 | Wiring Harness, Magneto, Modification of |
| S.B. 381C* | Woodruff Key Drive, Oil Pump, and Impeller Replacement (A D. #75-08-09) |